Strata CIX 200 Programming Manual Download Page 199 | Manualshive

Page: 199 / 508

background image

System

Miscellaneous System Commands

Strata CIX Programming Vol.1 12/09

4-39

System

801 Network Jack LAN Device Assignment

Prerequisite Program:

803 on

.

This assigns Strata CIX LAN parameters, enabling PC applications to connect to the BECU network jack.

1. Select > System > I/O Device.

2. Click the LAN Device tab.

3. Enter Program 801 data. Refer to

4.

Get

Default

sets all values to factory default.

5. Click

Submit

.

F

IELD

D

ESCRIPTION

00 LAN Port Index No.

Enter the port number of the LAN device to be assigned or select from the
list. Refer to

“803 Application Port Assignments”

Possible values:1~12 (default = no value)

01 Protocol

Select Communication Protocol.

Possible values:TCP (default) or UDP

Note

Select UDP for Network DSS and TCP for CIX applications.

02 Application Type

Select the Operation Type.

•

If Server is selected, make an entry in 04 Server Port Number.

•

If Client is selected, make an entry in 05 Client IP Address.

Possible values:Server (default) or Client

03 Data Flow

Select the data flow protocol for CIX and PC communications.

Possible values:Synchronous or Asynchronous (default = Asynchronous)

04 Server Port No.

Enter the Server Port Number and proceed to 07 Read Retry Number. This
field is required if Server was selected in 02 PC Operation Type above. If not,
leave this field blank and proceed to 05 Client IP Address.

Possible values:0~65535 (default = 0)

05 Client IP

Enter the Client LAN IP Address. This field is required if Client was selected
in 02 PC Operation Type above.

Possible values:0~255 for each octet (default = 0)

06 Client Port No.

Enter the Client Port number

Possible values: 0~65535 (default = 0)

For Central LAN SMDR in a Strata Net use the same port number if the
SMDR Application supports receiving data from multiple nodes on one port
(i.e. 6000). Use a unique port number in each node if the SMDR Application
does not support receiving data from multiple nodes on a single port (i.e.
Node 1=6000, Node 2=6001). Refer to

07 Read Retry No.

Set the maximum number of Read Retries.

Possible values: 0 ~ 10 (default = 1)

«
...
197
198
199
200
201
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: NEC Pages: 2

Brand: Samsung Pages: 19

Brand: Samsung Pages: 9

Brand: Samsung Pages: 107

Brand: Samsung Pages: 108

Brand: Samsung Pages: 3

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 118

Brand: Samsung Pages: 219

Brand: Samsung Pages: 26

Brand: Samsung Pages: 2

Brand: Samsung Pages: 222

Brand: Samsung Pages: 2

SGH-a887 Series

Brand: Samsung Pages: 189

Brand: Samsung Pages: 30

Intercept SPH-M810

Brand: Samsung Pages: 235

Brand: Samsung Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands