Strata CIX 200 Programming Manual Download Page 169 | Manualshive

Page: 169 / 508

background image

System

Dial Number Plan

Strata CIX Programming Vol.1 12/09

4-9

System

103 Class Of Service

Prerequisite Program:

None

Class of Service (COS) (1~32) assignments are made for users of telephones, attendant consoles, and
incoming calls based upon the line the call arrives or, in some cases, on a call-by-call basis when using
DISA or Tie Line with Q-Sig interfaces. For telephone users, the COS assignments are made for each of
the Day/Night Modes to allow different services during different parts of the day.

1. In Network eManager, click System > Class of Service.

2. COS Number – Select the COS Number (1~32).

3. Place a check mark in each of the services you wish to allow.

4.

Get

Default

sets all values to factory defaults.

5. Click

Submit

.

F

IELD

D

ESCRIPTION

01 Auto Busy Redial

Allow Automatic Busy Redial after dialing a busy outside
destination.

02 Call Forward Override

Allow Call Forward Override. If allowed, this station does not
forward calls from a calling station with System or Station Call
Forward activated. This includes when dialing from the dial pad
or DSS button located on the telephone or DSS console.

03 Call Transfer w/ Camp-on

Allows a call transferred by a station to Camp-on to a busy
destination.

04 Change DISA Codes

Allow stations to change the DISA security code.

05 DND Override - Calling

Party

Permits a caller to override the DND status of a station.

06 DND Override - Called

Party

Allows calling parties with DND Override privileges to override
DND status.

07 Do Not Disturb

Allows user to place stations on DND mode.

08 Remote Set/Reset DND

Provides stations with the ability to set/reset DND on other
phones.

09 Executive Override

Allow Executive Override on a call.

10 Executive Override

Allowed

Allow Executive Override for incoming callers.

11 Offhook Camp-on

Allow Off-hook Camp-on when encountering a busy destination.

12 Group Pickup

Allow stations for Group Call Pickup within one's own group.

13 Directed Station Pickup

Allow stations to pick another specific ringing station.

14 Directed Group Call

Pickup

Allow stations to pick up a ringing station in a specified group.

15 Directed DN Call Pickup

Allow stations to pick up a specified DN.

16 Ext Call Pickup

Allow stations to pick up any incoming trunk call.

«
...
167
168
169
170
171
...
»

Summary of Contents for CIX 200





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CIX 200

Brand: Bea-fon Pages: 70

Brand: Polycom Pages: 56

Capsat TT-3060A

Brand: Thrane&Thrane Pages: 182

Brand: BTECH Pages: 60

SimplePhone A50

Brand: Tesla Pages: 32

Brand: NAPCO Pages: 24

Brand: ShoreTel Pages: 2

Brand: Centrality Pages: 59

Brand: HTC Pages: 310

Brand: ALIGATOR Pages: 13

Brand: Sony Ericsson Pages: 54

Skyroute CL3050 ver 1.2

Brand: DSC Pages: 28

Brand: Cosmocom Pages: 22

Brand: Zte Pages: 2

Brand: Zte Pages: 48

Brand: Xiaomi Pages: 8

Brand: Xblue Networks Pages: 61

Anycall SGH-Z368

Brand: Samsung Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands