Stoll CMS 730 S Operating Instructions Manual Download Page 277

Page: 277 / 468

273

Setup Data

5.5 Setup2 Editor

5.5.1

Overview of the Setup2 Editor of the CMS

The Setup2 data will be displayed in the "Setup2 Editor".



Explanation

Row

Tabs of a menu

Table

Call-up the individual menus

Switch on or off the virtual keyboard



: The menu keys are covered by the active virtual keyboard.



Switch off the virtual keyboard in order to switch to another menu.

Activate and deactivate the state line (only display of the values, no window
call up possible)

Switch on or off the table tools

Undo the last editing of a line

Undo the last editing of a cell

Save all values of the actual tab (table)

Call up the online help of the selected tab.

: With file mode only

Save the Setup2 file (setx)

Summary of Contents for CMS 730 S





















































































































































































































































































































































































































































































Search results

Summary of Contents for CMS 730 S

Reviews:

Brands by name

Popular brands

Stoll CMS 730 S, Operating Instructions Manual

Search results

Summary of Contents for CMS 730 S

Reviews:

Brands by name

Popular brands