manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 75

Integrated Bus

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

75

11

11.2.2

IP address and subnet mask

An IP address is divided into a network section and a device section by the subnet mask. The subnet mask 

can be represented in binary format, for example, as a series of numbers with the left side consisting only of 

the number 1 and the right side consisting only of the number 0.

1111 1111.1111 1000.0000 0000.0000 0000 = 255.248.0.0

The section of the subnet mask with the number 1 shows which part of the IP address indicates the address 

of the subnet (the network section). The other part with the number 0 shows the part of the IP address that 

represents the address of the device in the subnet (device section).

The following example illustrates how to calculate the IP address.

The IP address 128.206.17.177 with subnet mask 255.240.0.0 is entered for the network interface of the 

computer:

Subnet mask:1111 1111.1111 0000.0000 0000.0000 0000

The 12 numbers on the left of the IP address indicate the address of the subnet and must be identical in the 

IP address of the device. The 20 number of the IP address on the right indicate the address of the computer 

in the subnet. This section must be different in the IP address of the device.

A possible IP address for the device could therefore be:

1000 0000.1100 1111.0001 0001.1011 0001 = 128.207.17.177

IP address:

1000 0000.1100 1110.0001 0001.1011 0001

Network section, must be 

identical in the device and 

PC

Device section, must be 

different in the device and PC

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands