manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 187

Diagnosis

O

peration

 man
ual 
POSIDYN

®

 SDS 

5000

18

7

ID 442

289

.06

WE KEEP THINGS MOVING

13

13.3.40 *ParaModul ERROR: ksb write error

13.3.41 *ConfigStartERROR parameters lost

Resolution

Level

Response

An error was detected when writing the 

configuration in the configuration memory.

—

The configuration does not start.

Possible cause

Test

Measure

Acknowledgement

Faulty flash memory.

—

Replace the Paramodule.

—

The configuration is too 

large for the configuration 

memory.

•

Apply a suitable configuration via 

POSITool and then save it (

A00

)

•

Replace the Paramodule.

Resolution

Level

Response

No parameter values are saved in the 

Paramodule.

—

The configuration does not start.

Possible cause

Test

Measure

Acknowledgement

The control part was 

switched off while 

A00

 

was active.

—

•

Apply a suitable configuration via 

POSITool and then save it (

A00

)

•

Replace the Paramodule.

—

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands