Stober POSIDYN SDS 5000 Operation Manual Download Page 178

Page: 178 / 196

Diagnosis

Operation

manual

POSIDYN®

SDS

5000

ID 44

22
8

WE KEEP THINGS MOVING

13.3.27 71:Firmware

Triggering

Level

Response

Fault counter

A firmware error was detected.

Fault

Causes 1 and 2 only occur when the device starts so that

the inverter can not be enabled. Cause 3 can also occur

during operation.

Z71

Cause

Description

Measure

Acknowledgement

1:FW defective

Only for SDS 5000: An active firmware

error was detected or faulty firmware

was detected in the firmware download

memory.

Reload the firmware using the

POSITool software. Also note the

Service section.

Switch device off/on

2:Activate FW!

Only for SDS 5000: The firmware was

loaded into the inverter but not yet

activated.

Activate the firmware and perform a

device restart. Also note the Service

section.

3:CRC error

A firmware error was detected.

Switch off the 24 vdc power supply and

switch it on again. If the error occurs

repeatedly, replace the inverter.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands