manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 141

Service

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

141

12

12.5.2.7

D96 Reference value generator

NOTICE

During this action, the motor shaft will move.

Make sure that the motor can turn freely during the action!

When you start the action, a square-shaped reference value is specified for the motor. You can parameterize 

the reference value in 

D93

 to 

D95

.

During activation, the enable must be inactive. If you have started the action in 

D96.0

, you must activate the 

enable.

The action can only be concluded by turning off the enable and quick stop! With a quick stop signal, the drive 

is halted immediately.

During the action, the cycle time is set internally to 32 msec.

You can read the following result from the third element (

D96.2

):

1: aborted:

 The action was aborted by turning off the enable.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands