STMicroelectronics STM32F405 Reference Manual Download | Manualshive

Page: 1691 / 1731

background image

DocID018909 Rev 11

RM0090

Debug support (DBG)

1701

For this, the debugger host must first set some debug configuration registers to change the
low-power mode behavior:

•

In Sleep mode, DBG_SLEEP bit of DBGMCU_CR register must be previously set by
the debugger. This will feed HCLK with the same clock that is provided to FCLK
(system clock previously configured by the software).

•

In Stop mode, the bit DBG_STOP must be previously set by the debugger. This will
enable the internal RC oscillator clock to feed FCLK and HCLK in STOP mode.

38.16.2 Debug support for timers, watchdog, bxCAN and I

2

C

During a breakpoint, it is necessary to choose how the counter of timers and watchdog
should behave:

•

They can continue to count inside a breakpoint. This is usually required when a PWM is
controlling a motor, for example.

•

They can stop to count inside a breakpoint. This is required for watchdog purposes.

For the bxCAN, the user can choose to block the update of the receive register during a
breakpoint.

For the I

2

C, the user can choose to block the SMBUS timeout during a breakpoint.

38.16.3 Debug

MCU

configuration register

This register allows the configuration of the MCU under DEBUG. This concerns:

•

Low-power mode support

•

Timer and watchdog counter support

•

bxCAN communication support

•

Trace pin assignment

This DBGMCU_CR is mapped on the External PPB bus at address 0xE0042004

It is asynchronously reset by the PORESET (and not the system reset). It can be written by
the debugger under system reset.

If the debugger host does not support these features, it is still possible for the user software
to write to these registers.

DBGMCU_CR register

Address: 0xE004 2004

Only 32-bit access supported

POR Reset: 0x0000 0000 (not reset by system reset)

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

Reserved

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Reserved

TRACE_

MODE

[1:0]

TRACE

_IOEN

Reserved

DBG_

STAND

BY

DBG_
STOP

DBG_

SLEEP

rw

rw

rw

rw

rw

rw

«
...
1689
1690
1691
1692
1693
...
»

Summary of Contents for STM32F405




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for STM32F405

Brand: ABATEC Pages: 8

Brand: M&C Pages: 16

Brand: Sole Diesel Pages: 8

Brand: Bartec Pages: 26

Brand: Baninni Pages: 26

Brand: V2 Pages: 48

Brand: Campbell Pages: 8

Brand: Campbell Pages: 22

Brand: Ublox Pages: 2

Brand: u-blox Pages: 19

Brand: Ultratec Pages: 33

Brand: Union Instruments Pages: 63

Brand: Bartlett Pages: 7

Brand: ZKTeco Pages: 20

Brand: ZKTeco Pages: 8

Brand: ZKTeco Pages: 10

Brand: ZKTeco Pages: 121

Brand: ZKTeco Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands