STMicroelectronics SPEAr300 Reference Manual Download Page 659 | Manualshive

Page: 659 / 844

background image

RM0082

RS_Reconfigurable array subsystem (RAS) registers

Doc ID 018672 Rev 1

Note:

If the register bit is '1', then the particular IP in the fixed part will be connected to PL_GPIO.
If the register bit is '0', then RAS_GPIO will be connected to PL_GPIO.

30.4.2

RAS Register 2 (0x99000004)

This register is used to select between different modes of the RAS IPs.

[12]

1’h0

SSP enhanced (CS(2-3-4))

[11]

1’h0

SSP Basic (no CS(2-3-4))

[10]

1’h0

MAC Ethernet

[09]

1’h0

basGPIO (0)

[08]

1’h0

basGPIO(1)

[07]

1’h0

basGPIO(2)

[06]

1’h0

basGPIO(3)

[05]

1’h0

basGPIO(4)

[04]

1’h0

basGPIO(5)

[03]

1’h0

UART enhanced (also others UART signals, such as DCD....)

[02]

1’h0

UART basic (only RX & TX signals)

[01]

1’h0

Timer B (timers 3/4)

[00]

1’h0

Timer A (timers 1/2)

Table 588.

RAS Register 1 description

Field

Default
Value

Description

Table 589.

RAS Register 2 description

Field

Default
Value

Description

[31]

1’h0

This bit is used for configuring the 48 MHz clock source for CLCD block.

'1' - Clock from external source (PL_CLK1)

'0' - 48 MHz clock

[30]

1’h0

This bit is used for configuring the ExtDevWidth input port of FSMC.

'1' - ExtDevWidth = 2'b01 => 16 bit external bus

'0' - ExtDevWidth = 2'b00 => 8 bit external bus

[29]

1’h0

This bit is used for configuring the accessibility of memory through either
SDIO or I2S.

'1' - SDIO is using the memory

'0' - I2S is using the memory

[28]

1’h0

This bit is used for muxing the DAC O1, O2 ports and the GPIO10_3 and
GPIO10_2 ports from the telecom block. This muxing is happening only when
LEND_IP_PHONE or HEND_IP_PHONE or LEND_WIFI_PHONE or
HEND_WIFI_PHONE is selected.

'

1' - GPIO10s from TELECOM

'0' - DAC ports

«
...
657
658
659
660
661
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: I-Tork Pages: 15

FX-COMM4NDER MFX3203

Brand: Magicfx Pages: 16

Brand: Auber Pages: 3

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Wilo Pages: 128

KaDe KDH-KZ620U

Brand: AAT Holding Pages: 28

Brand: Hanna Instruments Pages: 44

Brand: CLS Pages: 6

Brand: H3C Pages: 15

MediaDirector 2252B

Brand: Harmonic Pages: 2

Brand: CASTLE Pages: 2

TEMP2020M Series

Brand: Samwon Tech Pages: 105

Brand: Pilz Pages: 23

ProCon D300 Series

Brand: ICON Pages: 28

Brand: Silverline Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands