STMicroelectronics SPEAr300 Reference Manual Download Page 622 | Manualshive

Page: 622 / 844

background image

LS_I2C controller

RM0082

Doc ID 018672 Rev 1

Table 542.

IC_CON register bit assignments

Bit

Name

Type

Reset
value

Description

[15:07]

Reserved

-

Read: undefined. Write: should be zero.

[06]

IC_SLAVE_DISABLE

RW

1’h0

Slave disabled after reset.

This bit controls whether the I

2

C controller has

its slave disabled after reset, according to the
encoding:

1‘b0 = Enabled (default).

1‘b1 = Disabled.

[05]

IC_RESTART_EN

RW

1’h1

Enable restart conditions (when acting as
master).

This bit determines whether restart conditions
may be sent (if set to ‘b1) when acting as a
master or not (if set to ‘b0). Indeed, some older
slaves do not support handling restart
conditions.

Note: Disabling a restart does not allow the
master to perform the following function:

●

send multiple bytes per transfer (split),

●

change direction within a transfer (split),

●

send a start byte,

●

perform any high-speed mode operation,

●

perform combined format transfers in 7-
or 10 bit addressing mode (split for 7 bit),

●

perform a read operation with a 10 bit
address.

●

Split operations are broken down into
multiple I

2

C transfers with a stop and

start condition in between. The other
operations are not performed at all and
result in setting TX_ABRT.

[04]

IC_10BITADDR_MASTE
R

RO

1’h0

10 bit addressing mode (when acting as
master).
The function of this bit is handled by bit 12 of
IC_TAR. This bit is a read-only field called
IC_10BITADDR_MASTER_rd_only.

[03]

IC_10BITADDR_SLAVE

RW

1’h1

Responds to 7- or 10 bit addresses (when
acting as slave).
This bit controls if I

2

C controller responds to

either 7- or 10 bit addresses when acting as a
slave, according to the encoding:
1‘b0 = 7. The I

2

C controller ignores

transactions which involve 10 bit addressing.
for 7 bit addressing, only the lower 7 bits of the
IC_SAR register (

Section 28.6.5

) are

compared.
1‘b1 = 10. The I

2

C controller responds to only

10 bit addressing transfers that match the full
10 bits of the IC_SAR register.

«
...
620
621
622
623
624
...
»

Summary of Contents for SPEAr300













































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPEAr300

Brand: ABB Pages: 50

Brand: iCeeO2 Pages: 7

Brand: UE Pages: 4

Brand: Barco Pages: 6

Brand: ZKTeco Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Rain Bird Pages: 18

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

eTracer ET4415BND

Brand: Epsolar Pages: 44

Brand: Qorvo Pages: 6

Brand: Castell Pages: 7

Brand: Ultraflex Pages: 48

Brand: Ekinex Pages: 4

Brand: XINGDASHINE Pages: 3

Brand: ECO POWER Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands