manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

General-purpose timers (TIM2/TIM3/TIM4)

RM0365

589/1080

DocID025202 Rev 7

1.

Configure the external trigger input circuit by programming the TIMx_SMCR register as 
follows:
–

ETF = 0000: no filter 

–

ETPS=00: prescaler disabled

–

ETP=0: detection of rising edges on ETR and ECE=1 to enable the external clock 
mode 2.

2.  Configure the channel 1 as follows, to detect rising edges on TI: 

–

IC1F=0000: no filter. 

–

The capture prescaler is not used for triggering and does not need to be 
configured.

–

CC1S=01in TIMx_CCMR1 register to select only the input capture source

–

CC1P=0 and CC1NP=0 in TIMx_CCER register to validate the polarity (and detect 
rising edge only).

3.  Configure the timer in trigger mode by writing SMS=110 in TIMx_SMCR register. Select 

TI1 as the input source by writing TS=101 in TIMx_SMCR register.

A rising edge on TI1 enables the counter and sets the TIF flag. The counter then counts on 
ETR rising edges.

The delay between the rising edge of the ETR signal and the actual reset of the counter is 
due to the resynchronization circuit on ETRP input. 

Figure 231. Control circuit in external clock mode 2 + trigger mode

21.3.19 Timer 

synchronization

The TIMx timers are linked together internally for timer synchronization or chaining. When 
one Timer is configured in Master Mode, it can reset, start, stop or clock the counter of 
another Timer configured in Slave Mode.

Figure 232: Master/Slave timer example

 presents an overview of the trigger selection and 

the master mode selection blocks.

069

7,)

&RXQWHUUHJLVWHU

&RXQWHUFORFN &.B&17 &.B36&

(75

&(1&17B(1

7,

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
GE D20MX User Manual preview
D20MX
Brand: GE Pages: 146
NEC N8104-213 Installation Manual preview
N8104-213
Brand: NEC Pages: 10
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Xinje XG Series User Manual preview
XG Series
Brand: Xinje Pages: 76
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
Gate NanoAAB User Manual preview
NanoAAB
Brand: Gate Pages: 8
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Brand: National Instruments Pages: 15
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
Rolls HR11C - SCHEMA Wiring Diagram preview
HR11C - SCHEMA
Brand: Rolls Pages: 1
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Brand: Intel Pages: 112
S&T Kontron CP3005 Series User Manual preview
Kontron CP3005 Series
Brand: S&T Pages: 115
Intel Braswell Series Technical Manual preview
Braswell Series
Brand: Intel Pages: 54

Brands by name

Popular brands

Load more brands