manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

320/1080

RM0365

Analog-to-digital converters (ADC)

392

         

15.3.23  End of conversion, end of sampling phase (EOC, JEOC, EOSMP)

The ADC notifies the application for each end of regular conversion (EOC) event and each 
injected conversion (JEOC) event.

The ADC sets the EOC flag as soon as a new regular conversion data is available in the 
ADCx_DR register. An interrupt can be generated if bit EOCIE is set. EOC flag is cleared by 
the software either by writing 1 to it or by reading ADCx_DR.

The ADC sets the JEOC flag as soon as a new injected conversion data is available in one 
of the ADCx_JDRy register. An interrupt can be generated if bit JEOCIE is set. JEOC flag is 
cleared by the software either by writing 1 to it or by reading the corresponding ADCx_JDRy 
register.

The ADC also notifies the end of Sampling phase by setting the status bit EOSMP (for 
regular conversions only). EOSMP flag is cleared by software by writing 1 to it. An interrupt 
can be generated if bit EOSMPIE is set.

15.3.24 End 

of 

conversion sequence (EOS, JEOS)

The ADC notifies the application for each end of regular sequence (EOS) and for each end 
of injected sequence (JEOS) event.

The ADC sets the EOS flag as soon as the last data of the regular conversion sequence is 
available in the ADCx_DR register. An interrupt can be generated if bit EOSIE is set. EOS 
flag is cleared by the software either by writing 1 to it.

The ADC sets the JEOS flag as soon as the last data of the injected conversion sequence is 
complete. An interrupt can be generated if bit JEOSIE is set. JEOS flag is cleared by the 
software either by writing 1 to it.

Table 89. T

SAR

 timings depending on resolution

RES 

(bits)

T

SAR

 

(ADC clock cycles)

T

SAR

 (ns) at 

F

ADC

=72 MHz

T

ADC

 (ADC clock cycles) 

(with Sampling Time=
1.5 ADC clock cycles)

T

ADC

 (ns) at 

F

ADC

=72 MHz

12

12.5 ADC clock cycles 173.6 ns

14 ADC clock cycles

194.4 ns

10

10.5 ADC clock cycles 145.8 ns

12 ADC clock cycles

166.7 ns

8

8.5 ADC clock cycles

118.0 ns

10 ADC clock cycles

138.9 ns

6

6.5 ADC clock cycles

90.3 ns

8 ADC clock cycles

111.1 ns

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
Paradyne COMSPHERE 3610 User Manual preview
COMSPHERE 3610
Brand: Paradyne Pages: 112
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Brand: ebm-papst Pages: 16
Renesas Converter Board R0E5212BACFG00 User Manual preview
Converter Board R0E5212BACFG00
Brand: Renesas Pages: 6
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Brand: ebm-papst Pages: 13
Idis DR-6308P Quick Manual preview
DR-6308P
Brand: Idis Pages: 20
Ubiquiti UniFi LED ULED-AT Quick Start Manual preview
UniFi LED ULED-AT
Brand: Ubiquiti Pages: 16
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Brand: Corsair Pages: 30
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Brand: A.E.B. Pages: 28
FDI USB-ICP-SAB9 Quick Start Manual preview
USB-ICP-SAB9
Brand: FDI Pages: 15
Adaptec ASR-3085 Important Information About Issues And Errata preview
ASR-3085
Brand: Adaptec Pages: 3
Boardcon Embedded Design EM3568 User Manual preview
EM3568
Brand: Boardcon Embedded Design Pages: 36
HIKVISION DS-7600NI-H2/4P Series Installation Manual preview
DS-7600NI-H2/4P Series
Brand: HIKVISION Pages: 14

Brands by name

Popular brands

Load more brands