manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

DocID025202 Rev 7

296/1080

RM0365

Analog-to-digital converters (ADC)

392

In differential input mode, the analog voltage to be converted for channel “i” is the difference 
between the external voltage ADC_IN

i

 (positive input) and ADC_IN

i+1

 (negative input).

For a complete description of how the input channels are connected for each ADC, refer to 

Figure 53: ADC1 and ADC2 connectivity on page 294

. 

Caution:

When configuring the channel “i” in differential input mode, its negative input voltage is 
connected to ADC_IN

i+1

. As a consequence, channel “

i+1

” is no longer usable in single-

ended mode or in differential mode and must never be configured to be converted.
Some channels are shared between ADC1 and ADC2: this can make the channel on the 
other ADC unusable. Only exception is interleave mode for ADC master and the slave.

Example: Configuring ADC1_IN5 in differential input mode will make ADC12_IN6 not 
usable: in that case, the channels 6 of both ADC1 and ADC2 must never be converted.

Note:

Channels 16, 17 and 18 of ADC1 and channels 17 and 18 of ADC2 are connected to 
internal analog channels and are internally fixed to single-ended inputs configuration 
(corresponding bits DIFSEL[i] is always zero). Channel 15 of ADC1 is also an internal 
channel and the user must configure the corresponding bit DIFSEL[15] to zero.

15.3.8 Calibration 

(ADCAL, 

ADCALDIF, ADCx_CALFACT)

Each ADC provides an automatic calibration procedure which drives all the calibration 
sequence including the power-on/off sequence of the ADC. During the procedure, the ADC 
calculates a calibration factor which is 7-bit wide and which is applied internally to the ADC 
until the next ADC power-off. During the calibration procedure, the application must not use 
the ADC and must wait until calibration is complete.

Calibration is preliminary to any ADC operation. It removes the offset error which may vary 
from chip to chip due to process or bandgap variation. 

The calibration factor to be applied for single-ended input conversions is different from the 
factor to be applied for differential input conversions:

•

Write ADCALDIF=0 before launching a calibration which will be applied for single-
ended input conversions.

•

Write ADCALDIF=1 before launching a calibration which will be applied for differential 
input conversions.

The calibration is then initiated by software by setting bit ADCAL=1. Calibration can only be 
initiated when the ADC is disabled (when ADEN=0). ADCAL bit stays at 1 during all the 
calibration sequence. It is then cleared by hardware as soon the calibration completes. At 
this time, the associated calibration factor is stored internally in the analog ADC and also in 
the bits CALFACT_S[6:0] or CALFACT_D[6:0] of ADCx_CALFACT register (depending on 
single-ended or differential input calibration)

The internal analog calibration is kept if the ADC is disabled (ADEN=0). However, if the ADC 
is disabled for extended periods, then it is recommended that a new calibration cycle is run 
before re-enabling the ADC.

The internal analog calibration is kept if the ADC is disabled (ADEN=0). When the ADC 
operating conditions change (V

REF+

 changes are the main contributor to ADC offset 

variations, V

DDA

 and temperature change to a lesser extent), it is recommended to re-run a 

calibration cycle.

The internal analog calibration is lost each time the power of the ADC is removed (example, 
when the product enters in STANDBY or VBAT mode). In this case, to avoid spending time 
recalibrating the ADC, it is possible to re-write the calibration factor into the 

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
H3C SecPath F50X0 Series Manual preview
SecPath F50X0 Series
Brand: H3C Pages: 41
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Brand: ActiveEye Pages: 35
Data Translation DT9835 Getting Started Manual preview
DT9835
Brand: Data Translation Pages: 62
Moxa Technologies CP-102N-T Quick Installation Manual preview
CP-102N-T
Brand: Moxa Technologies Pages: 8
Hanwha Techwin WISENET XRN-1610 User Manual preview
WISENET XRN-1610
Brand: Hanwha Techwin Pages: 88
Dahua DHI-NVR5208-4KS2 User Manual preview
DHI-NVR5208-4KS2
Brand: Dahua Pages: 361
Dahua NVR5208-EI User Manual preview
NVR5208-EI
Brand: Dahua Pages: 489
MTL 9468-ET Instruction Manual preview
9468-ET
Brand: MTL Pages: 12
Citizen IF1-ET01 User Manual preview
IF1-ET01
Brand: Citizen Pages: 26
InfoStor RAID 6 Information Sheet preview
RAID 6
Brand: InfoStor Pages: 6
Domburg Switch Polarization Print HPP4 Quick Start Manual preview
Switch Polarization Print HPP4
Brand: Domburg Pages: 11
MikroTik CCR1009-7G-1C-1S+ Quick Manual preview
CCR1009-7G-1C-1S+
Brand: MikroTik Pages: 9
Motorola DigitalDNA ColdFire MCF5272 User Manual preview
DigitalDNA ColdFire MCF5272
Brand: Motorola Pages: 550
Motorola DigitalDNA MPC180E User Manual preview
DigitalDNA MPC180E
Brand: Motorola Pages: 112
Zte MC315 User Manual preview
MC315
Brand: Zte Pages: 29

Brands by name

Popular brands

Load more brands