manualshive.com logo in svg

STMicroelectronics RM0365, Reference Manual

The STMicroelectronics RM0365 Reference Manual is the comprehensive guide for successfully operating and maximizing the potential of your device. This invaluable resource is available for free download at manualshive.com, ensuring easy access to detailed instructions and information necessary for efficient product utilization.

Share
Download
background image

Debug support (DBG)

RM0365

1053/1080

DocID025202 Rev 7

33.13 

DWT (data watchpoint trigger)

The DWT unit consists of four comparators. They are configurable as:

•

a hardware watchpoint or

•

a trigger to an ETM or

•

a PC sampler or

•

a data address sampler

The DWT also provides some means to give some profiling informations. For this, some 
counters are accessible to give the number of:

•

Clock cycle

•

Folded instructions

•

Load store unit (LSU) operations

•

Sleep cycles

•

CPI (clock per instructions)

•

Interrupt overhead

33.14 

MCU debug component (DBGMCU)

The MCU debug component helps the debugger provide support for: 

•

Low-power modes

•

Clock control for timers, watchdog, I2C and bxCAN during a breakpoint

•

Control of the trace pins assignment

33.14.1 Debug 

support 

for low-power modes

To enter low-power mode, the instruction WFI or WFE must be executed.

The MCU implements several low-power modes which can either deactivate the CPU clock 
or reduce the power of the CPU.

The core does not allow FCLK or HCLK to be turned off during a debug session. As these 
are required for the debugger connection, during a debug, they must remain active. The 
MCU integrates special means to allow the user to debug software in low-power modes.

For this, the debugger host must first set some debug configuration registers to change the 
low-power mode behavior:

•

In Sleep mode, DBG_SLEEP bit of DBGMCU_CR register must be previously set by 
the debugger. This will feed HCLK with the same clock that is provided to FCLK 
(system clock previously configured by the software).

•

In Stop mode, the bit DBG_STOP must be previously set by the debugger. This will 
enable the internal RC oscillator clock to feed FCLK and HCLK in STOP mode.

Summary of Contents for RM0365

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RM0365

PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
Zoom B9.1ut Operation Manual preview
B9.1ut
Brand: Zoom Pages: 88
EK-Quantum Momentum ROG Strix X570-E D-RGB User Manual preview
Momentum ROG Strix X570-E D-RGB
Brand: EK-Quantum Pages: 10
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Brand: Datasat Pages: 24
S&T Kontron SMARC-sXEL User Manual preview
Kontron SMARC-sXEL
Brand: S&T Pages: 108
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
SMC Sierra Monitor FPC-N38 Startup Manual preview
FPC-N38
Brand: SMC Sierra Monitor Pages: 43
Zhone 891630 System Reference Manual preview
891630
Brand: Zhone Pages: 494
V7 SCREENSHARE PRO User Manual preview
SCREENSHARE PRO
Brand: V7 Pages: 4
PairGain 150-1504-15 Manual preview
150-1504-15
Brand: PairGain Pages: 68
Aegis AVP-DE1K-100 User Manual preview
AVP-DE1K-100
Brand: Aegis Pages: 7
Citizen IF1-WF04 User Manual preview
IF1-WF04
Brand: Citizen Pages: 50
MSI TV@nywhere Satellite Install Manual preview
TV@nywhere Satellite
Brand: MSI Pages: 2

Brands by name

Popular brands

Load more brands