Still RCG15 Original Instructions Manual Download Page 98

Page: 98 / 182

DANGER

Risk of injury!

–

Do not step on the fork.

DANGER

Risk of injury!

–

Do not step under the raised forks.

DANGER

People may be injured in the danger area of the

truck!
The danger area of the truck must be completely

clear of all personnel, except the driver in his normal

operating position. If persons fail to leave the danger

area despite warnings:

–

Cease work with the truck immediately.

–

Secure the truck against use by unauthorised par-

ties.

DANGER

Danger of death from falling loads!

–

Never walk or stand underneath suspended loads.

Transporting suspended loads

Before transporting suspended loads, consult

the national regulatory authorities (in Germa-

ny, the employer's liability insurance associa-

tions).
National regulations may place restrictions on

these operations. Contact the relevant authori-

ties.

DANGER

Suspended loads that begin to swing can result in

the following risks:

●

Impaired braking and steering action

●

Tipping over the load wheels or drive

wheels

●

Tipping the truck at right angles to the direc-

tion of travel

6210_001-007



Use and Operation

Handling loads

60048011601 EN - 08/2020

Summary of Contents for RCG15























































































































































































Search results

Summary of Contents for RCG15

Reviews:

Related manuals for RCG15

Brands by name

Popular brands

Still RCG15, Original Instructions Manual

Search results

Summary of Contents for RCG15

Reviews:

Related manuals for RCG15

Brands by name

Popular brands