Still RCG15 Original Instructions Manual Download Page 61

Page: 61 / 182

Seat belt status and performance

checks

DANGER

For safety reasons, the condition and protective

ability of the seat belt must be checked on a daily

basis.
Do not operate the vehicle with the seat belt re-

moved.

–

Check the condition of the belt: pull the seat

belt(1) all the way out of the retractor(2) and

check the seat belt for damage.

CAUTION

The seat belt must be replaced if it is cracked, worn

or has been damaged in an accident.

–

Carefully check the connection between the

seat belt and the seat.

–

Carefully check the connection between the

seat and the panel cover below.

NOTE

Only when the driver sits on the seat, the fork-

lift can be operated.

–

Push the lever (1)on the front left-hand side

of the engine bonnet upwards with your left

hand.

–

Open the bonnet and raise it around 30°.

NOTE

The bonnet is held up by the gas spring.



Use and Operation

Remaining ready for operation

60048011601 EN - 08/2020

Summary of Contents for RCG15























































































































































































Search results

Summary of Contents for RCG15

Reviews:

Related manuals for RCG15

Brands by name

Popular brands

Still RCG15, Original Instructions Manual

Search results

Summary of Contents for RCG15

Reviews:

Related manuals for RCG15

Brands by name

Popular brands