Still RCG15 Original Instructions Manual Download Page 14

Page: 14 / 182

Attachments

Attachments shall only be used as permitted.

The driver shall be instructed in the handling

of attachments.
The attachment operating instructions are en-

closed for trucks that are delivered from the

factory with an attachment. Before commis-

sioning a truck with an attachment, you must

check that loads are handled securely. De-

pending on the type of attachment, it may be

necessary to make adjustments, e.g. pressure

settings or adjusting stops and operating

speeds. See the attachment operating instruc-

tions for the corresponding instructions.
If attachments are not supplied with the indus-

trial truck, the specifications of the industrial

truck manufacturer and the attachment manu-

facturer must be observed.
The attachments and the connection of power

supplies for powered attachments may only be

made by specialists in accordance with the

specifications of the manufacturer. The proper

functioning of the attachments shall be

checked after each installation before initial

use.

The permissible carrying capacity of the at-

tachments and the permitted load of the indus-

trial truck (carrying capacity and load moment)

combined with the attachments shall not be

exceeded., refer to additional capacity rating

plate.
Modifications, in particular attachments or

conversions, are not permitted to be made to

the industrial truck without the manufacturer’s

approval.

Trailers

Industrial trucks may only be used to tow trail-

ers if they are intended for this purpose by the

manufacturer and if they are fitted with the ap-

propriate trailer coupling. The maximum towed

load specified in the operating instructions for

unbraked or braked trailers must not be ex-

ceeded.
The towing industrial truck must be operated

in such away that safe driving and braking of

the towed vehicle is ensured for all driving

movements.

Impermissible use

The operating company or driver, and not the

manufacturer, is liable for any hazards caused

by improper use.

NOTE

Please observe the definition of the following

responsible persons: "operating company"

and "driver".

Use for purposes other than those described

in these operating instructions is prohibited.

DANGER

There is a risk of fatal injury from falling

off the truck while it is moving!

–

It is prohibited to carry passengers on

the truck.

Introduction

Impermissible use

60048011601 EN - 08/2020

Summary of Contents for RCG15























































































































































































Search results

Summary of Contents for RCG15

Reviews:

Related manuals for RCG15

Brands by name

Popular brands

Still RCG15, Original Instructions Manual

Search results

Summary of Contents for RCG15

Reviews:

Related manuals for RCG15

Brands by name

Popular brands