Still FXH 20 Original Instructions Manual Download Page 24

Page: 24 / 140

Safety

Emissions

Noise emission values

Calculated during the test cycle performed in

accordance with standard EN 12053.

Acoustic pressure level in the driver's com-

partment
FXH 20

PAZ

68 dB (A)

FXH 25

PAZ

68 dB (A)

Uncertainty

2.5 dB (A)

NOTE

Lower or higher noise values may occur when

using industrial trucks, e.g. due to the mode

of operation, environmental factors and other

sources of noise.

Vibration characteristics for vibrations to which the body is exposed

The values were determined according to EN

13059 using trucks with standard equipment

according to the datasheet (driving over test

course with humps).

Speciﬁed characteristics for upper limb

vibrations
Vibration characteristics

< 2.5 m/s

NOTE

The vibration characteristics for bodily vibra-

tions cannot be used to determine the actual

load level of vibrations during operation. This

depends on the operating conditions (state of

ground, mode of operation etc.) and should

therefore be determined on site, where appro-

priate. It is mandatory to specify the hand-arm

vibrations even where the values do not indi-

cate any hazard, as in this case.

11548011751 EN - 10/2018

Summary of Contents for FXH 20













































































































































Search results

Summary of Contents for FXH 20

Reviews:

Brands by name

Popular brands

Still FXH 20, Original Instructions Manual

Search results

Summary of Contents for FXH 20

Reviews:

Brands by name

Popular brands