Still FXD 20 Original Instructions Manual Download Page 65

Page: 65 / 162

Starting the truck

DANGER

Risk of sparks
It is prohibited to use the truck with the battery hood

open.

–

Check that the battery hood is closed.

–

Check that the battery is locked.

DANGER

Risk of serious injury
Always keep your body inside the driver's compart-

ment while the truck is moving.

NOTE

Check that no controls are activated before

switching on the truck.

NOTE

Check that the battery is connected and

locked and that the hood is closed correctly.

To start the truck, proceed as follows:

–

Step onto the truck.

–

Sit on the seat and adjust it.

–

Adjust the floor.

–

Pull the emergency off switch (2).

–

Turn the key. For models equipped with an

electronic key, enter the 5-digit PIN to start

the truck (3).

The display (4) switches on.

–

Press the operator presence pedal (5) or (6)

(depending on the version).

–

Select the direction of travel (for the single-

pedal version).

–

Press the parking brake button to release

the parking brake (1).

The truck is now ready for use.



Use

Driving

11648011751 EN - 02/2021 - 06

Summary of Contents for FXD 20



































































































































































Search results

Summary of Contents for FXD 20

Reviews:

Related manuals for FXD 20

Brands by name

Popular brands

Still FXD 20, Original Instructions Manual

Search results

Summary of Contents for FXD 20

Reviews:

Related manuals for FXD 20

Brands by name

Popular brands