Still FXD 20 Original Instructions Manual Download Page 107

Page: 107 / 162

Driving assistance system: Dynamic Drive Control

Description of the Dynamic Drive

Control

The Dynamic Drive Control option is a sys-

tem that assists when driving and using the

truck.
The forklift operator must remain vigilant un-

der all circumstances and adhere to the truck

capacity plate.

CAUTION

Risk of accident
Despite this option, the forklift operator must remain

vigilant. The safety guidelines must be observed.

A specific screen for this option is available on

the display. The screen is only displayed when

double-stacking is in operation.
No indication of the weight present on the

forks is given. Only the maximum weight (1) is

communicated when present on the forks.
The load on the load arms, Q2 (4), must be

greater than or equal to the load on the forks,

Q1 (3).
The maximum speed of the truck depends on

the height of the forks.
The vertical bars (2) inform the operator of the

speed configuration of the truck. The diagram

is displayed only when double-stacking is in

operation. It indicates if the speed is high, me-

dium or low.
The speed varies depending on the load on

the forks between 0.3 and 1.8 metres. The

heavier the load, the lower the speed.
The forklift operator must remain cautious and

adjust the speed to suit the environmental

conditions.

CAUTION

Risk of incorrect use of the truck.
The forklift operator must be trained in and familiar

with the various features of this option.



Use

Driving assistance system: Dynamic Drive Control

11648011751 EN - 02/2021 - 06

Summary of Contents for FXD 20



































































































































































Search results

Summary of Contents for FXD 20

Reviews:

Related manuals for FXD 20

Brands by name

Popular brands

Still FXD 20, Original Instructions Manual

Search results

Summary of Contents for FXD 20

Reviews:

Related manuals for FXD 20

Brands by name

Popular brands