Still EXD 18 Original Instructions Manual Download Page 53

Page: 53 / 146

–

Operate it progressively in the opposite di-

rection until the required speed is reached.

Optispeed

–

Lower the tiller.

NOTE

The machine is only in the driving position in

zones (2) and (3). In the lower zone (4) or the

upper zone (1), the brake is applied and the

traction motor is switched off.

In zone (3), the truck can be used at full

speed. The traction speed is proportional to

the drive direction selector activation.
In zone (2), the maximum authorised speed

varies according to the position of the tiller.

Brake action zone

Maximum speed authorisation zone

Maximum speed automatic authorisation

zone

Maximum speed curve



Use

Driving

1160 801 15 51 EN - 02/2021 - 11

Summary of Contents for EXD 18



















































































































































Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands

Still EXD 18, Original Instructions Manual

Search results

Summary of Contents for EXD 18

Reviews:

Related manuals for EXD 18

Brands by name

Popular brands