manualshive.com logo in svg

Still EXD 18, Original Instructions Manual

Share
Download
Still EXD 18 Original Instructions Manual Download Page 121

Checking the battery acid level and

electrolyte density 

 WARNING

The electrolyte (diluted sulphuric acid) is poisonous

and caustic!

–

Always wear suitable protective equipment (indus-

trial goggles, safety gloves) when working on a

battery.

–

Never wear a watch or jewellery when handling

battery acid.

–

Do not allow any acid to get onto the clothing or

skin or into the eyes. If this does happen, rinse im-

mediately with plenty of clean water.

–

Immediately rinse away any spilled battery acid

with plenty of water.

–

In case of injury, seek medical advice immediate-

ly.

–

Always follow the safety information provided by

the battery manufacturer.

–

Comply with the regulations in force.

–

Check the battery acid level and electrolyte

density according to the battery manufactur-

er's recommendations.

–

The cell covers of the battery must be kept

dry and clean.

–

Any spillage of battery acid must be neutral-

ised immediately.

 ENVIRONMENT NOTE

Dispose of any used battery acid in accord-

ance with the regulations.

Maintenance

5

Electrical equipment

 111

1160 801 15 51 EN - 02/2021  -  11

Summary of Contents for EXD 18



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands