manualshive.com logo in svg

Still EXD 18, Original Instructions Manual

Share
Download
Still EXD 18 Original Instructions Manual Download Page 114

Chassis, bodywork and fittings

Cleaning the truck

Cleaning instructions

–

Park the truck.

–

Pull the emergency stop handle.

 CAUTION

The battery must always be disconnected during

cleaning procedures.

Washing the outside of the truck

 WARNING

–

Do not use flammable liquids to clean the truck.

–

The safety rules set out above must be followed to

prevent spark formation. They could lead to a

short circuit.

–

All components that are sensitive to moisture (par-

ticularly electric components) must be protected

when the truck is cleaned.

–

Follow the manufacturer's instructions when using

the cleaning product.

–

Clean the truck with a non-flammable clean-

ing product mixed with water, a sponge and

cloths.

–

Specifically clean the oil filler holes and sur-

rounding area as well as the lubricating nip-

ples (before lubrication).

 NOTE

A frequently cleaned truck must be lubricated

more regularly.

Cleaning the electrical installations

 WARNING

Do not expose electrical equipment (especially mo-

tors) to direct jets.

Maintenance

5

Chassis, bodywork and fittings

 104

1160 801 15 51 EN - 02/2021  -  11

Summary of Contents for EXD 18



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands