Still CX-M 10 Operating Instructions Manual Download Page 72

Page: 72 / 152

Operation

Handling loads

the area within the range of falling loads or a

descending working device.

WARNING

Danger of personal injury
Do not step on the forks.

WARNING

Persons can be injured in the danger zone of the

truck.
No person, except the driver in his normal operating

position, may stand in the danger zone of the truck.

If persons refuse to leave the danger zone despite

warnings, stop working with the truck immediately

and secure it against use by unauthorized persons.

DANGER

Danger of accidents through falling

loads!
Do not step or stand under a raised

load.

1044_800-004

Palletising a load

Only stack pallets not exceeding the specified

maximum dimensions. Do not stack damaged

transport aids and improperly formed load

units.
Place and secure the load on the lifting device

in such a way that it cannot move or fall off.
Stack the load units so that the specified aisle

width is not reduced by protruding parts.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands