Still CX-M 10 Operating Instructions Manual Download Page 61

Page: 61 / 152

Operation

Driving

123

456

789

PRG

1044_501-003

Driving forward

– Depress the top part of the throttle (2) or (3)

with the thumb.

– Truck speed is increased by depressing the

travel control further.

– When the travel control is released, the

truck is braked electrically.

Reversing

– Depress the lower part of the throttle (2) or

(3) with the thumb.

– Truck speed is increased by depressing the

travel control further.

– When the travel control is released, the

truck is braked electrically.

Reversing direction

– Allow the travel control to return to its neutral

position.

– Operate the travel control progressively

in the opposite direction of travel until the

desired speed is reached.

123

456

789

PRG

1044_503-001

Selecting the driving mode

NOTE

The pallet truck has 2 selectable driving mo-

des.

– For regular driving depress the

hare

button

(3).

– For driving with gentle acceleration depress

the

tortoise

button (2).

NOTE

The travel control (4) and (5) can be operated

with both the left and the right hand. Always

operate the travel control slowly to avoid jerky

starting, braking or reverslng.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands