Still CX-M 10 Operating Instructions Manual Download Page 59

Page: 59 / 152

Operation

Driving

WARNING

Danger of personal injury
Do not step on the forks.

WARNING

Persons can be injured in the danger zone of the

truck.
No person, except the driver in his normal operating

position, may stand in the danger zone of the truck.

If persons refuse to leave the danger zone despite

warnings, stop working with the truck immediately

and secure it against use by unauthorized persons.

DANGER

Danger of accidents through falling

loads!
Do not step or stand under a raised

load.

Persons in the danger area

Before starting up, the driver must ensure that

no person is standing in the danger area of the

truck.
A warning signal must be given in the event of

an impending danger to persons. If these per-

sons refuse to leave the danger area despite

the warning, the driver must stop work with the

vehicle immediately.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands