Still CX-M 10 Operating Instructions Manual Download Page 48

Page: 48 / 152

Operation

Intended use of the trucks

CAUTION

This machine is designed for order picking (coll-

ecting and gathering together items stored in the

warehouse before dispatch), horizontal transport

tasks and entering and removing pallets to and from

stock.
The dimensions and capacity of the trailers, pallets

or containers must be adapted to the load being

transported and must ensure stability.
The table of characteristics and performance at-

tached to this user manual gives you some of the

information you need to check that the equipment

is suitable for the work being carried out.
Any specific usage must be authorised by the site

manager; an analysis of the potential risks associa-

ted with this usage will enable him to put in place

any necessary additional safety measures.

Checks and actions prior to use

Daily pre-operational checks and

services

WARNING

Do not operate the truck until it is properly repaired

if any damage or faults are detected on the truck

or attachment (Option) during the following inspec-

tions. Safety features and switches must not be

removed or disabled. Fixed settings must not be

altered.

– Report any faults to the supervisors.

WARNING

Operation of the truck is only permissible with the

lids and flaps closed and with all covers in place.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands