background image

avoids accelerated wear. The product code

which appears

on the label and

on the packaging (table with recommendations

for use) is an aid to selection

STIHL composite resin cutting wheels are suita‐

ble, depending on the version, for cutting the fol‐

lowing materials:

Asphalt

Concrete

Stone

Ductile cast iron pipes

Steel; STIHL composite resin cutting wheels

are not suitable for cutting railway tracks

Do not cut any other materials – risk of accident!

6

Diamond Abrasive Wheels

For wet applications.
The proper selection and use of diamond abra‐

sive wheels ensures economical use and avoids

accelerated wear. The product code which

appears

on the label and

on the packaging (table with recommendations

for use) is an aid to selection

STIHL diamond abrasive wheels are suitable,

depending on the version, for cutting the follow‐

ing materials:

Asphalt

Concrete

Stone (hard stone)

Abrasive concrete

Fresh concrete

Clay brick

Clay pipe

Ductile cast iron pipe

Do not cut any other materials – Risk of accident!
Never use diamond abrasive wheels with side

plating as they jam in the cut and can result in

extreme kickback – Risk of accident!

6.1

Product Codes

0000-GXX-1235-A0

D-B10

The product code is a combination of letters and

numbers, consisting of up to four characters:

the letters denote the main field of application

of the abrasive wheel

the numbers denote the performance class of

the STIHL diamond abrasive wheel

6.2

Axial and radial run-out

A faultless spindle bearing of the cut-off machine

is necessary for a long service life and efficient

functioning of the diamond abrasive wheel.
Using the abrasive wheel on a cut-off machine

with a faulty spindle bearing can lead to devia‐

tions in radial and axial run-out.

An excessively high radial run-out deviation (A)

overloads individual diamond segments, which

overheat in the process. This can lead to stress

cracks in the parent wheel or to annealing of indi‐

vidual segments.
Deviations in axial run-out (B) result in higher

thermal loading and wider cuts.

English

6 Diamond Abrasive Wheels

14

0458-753-8321-C

Summary of Contents for TS 480i





































Reviews: