Stihl MS 881 Instruction Manual Download

Page: 16 / 32

0000-GXX-2937-A0

► Pull the starter grip slowly with your right hand

until you feel it engage.

► Pull the starter grip quickly and allow the

starter rope to rewind several times until the

engine runs.

► Press the throttle trigger lockout (5) and keep

pressed.

► Blip the throttle trigger (4).

The master control lever (3) springs to position

. The engine runs at idling speed.

NOTICE

■ Do not accelerate the engine with the chain

brake engaged since this can damage the

chain brake.

► Disengage the chain brake before you start

cutting.

► Disengage the chain brake.

The chainsaw is ready for use.

► If the saw chain rotates while the engine is

idling: See troubleshooting.

Idle speed adjustment is not correct.

► If the engine does not start: Prepare the

engine for the start and then try again to start

the engine.

9.4

Stopping the Engine

0000-GXX-A375-A0

► Release the throttle trigger (2) and lockout

lever (3).

The saw chain stops running.

► Move the Master Control lever (1) to posi‐

tion .

The engine stops and the Master Control lever
(1) springs back to position .

10 Checking the Saw

10.1

Checking the Chain Sprocket

► Shut off the engine.

► Disengage the chain brake.

► Remove the chain sprocket cover.

► Remove the bar and chain.

0000-GXX-3162-A0

► Use a STIHL gauge to check the wear marks

on the sprocket.

► If wear marks are deeper than a = 0.5 mm: Do

not use your chainsaw and contact your

STIHL servicing dealer for assistance.

The chain sprocket must be replaced.

10.2

Checking the Guide Bar

► Shut off the engine and engage the chain

brake.

► Remove the chain and guide bar.

0000-GXX-1217-A0

► Measure depth of bar groove with scale on

STIHL filing gauge.

► Install a new guide bar if one of the following

points applies:

–

Guide bar is damaged.

–

Measured bar groove depth is less than

specified minimum depth, 19.3.

–

Bar groove is pinched or splayed.

► If you have any queries: Contact your STIHL

servicing dealer for assistance.

10.3

Checking the Saw Chain

► Shut off the engine and engage the chain

brake.

English

10 Checking the Saw

0458-890-8321-B. VA0.A21.

Summary of Contents for MS 881

































Search results

Summary of Contents for MS 881

Reviews:

Related manuals for MS 881

Brands by name

Popular brands

Stihl MS 881, Instruction Manual

Search results

Summary of Contents for MS 881

Reviews:

Related manuals for MS 881

Brands by name

Popular brands