Stihl FS 240 Service Manual Download | Manualshive

Page: 109 / 134

background image

108

FS 240 C, FS 260 C, FS 360 C, FS 410 C, FS 460 C-M

11.8.2 Removal and installation

– Remove the carburetor,

:

Pry out the tank vent (1) via the
mounting rib (arrow)

– Remove tank vent (1) from hose

(2), examine and replace if
necessary

– Remove the grommet

Always fit a new tank vent.

Installation

:

Orient grommet (1) so that the
cone faces the fuel tank

– Coat outside of grommet with

STIHL press fluid,

:

Press grommet (1) into
hole (arrow) until it encloses the
hole completely

1

2

5904RA433 TG

1

5904RA434 TG

– Coat mounting surface of tank

vent with STIHL press fluid,

– Push new tank vent into hose

:

Orient tank vent (1) so that the
connector with hose lines up with
the opening (arrow)

:

Press tank vent (1) with hose
completely into the grommet

Hose must be pressed completely
onto the connectors of the tank vent
and the filter housing and run so
that it is free of kinks.

– Reassemble remaining parts in

reverse order

11.9

Fuel intake

11.9.1 Pickup body

Impurities which are entrained into
the fuel tank with the fuel are
trapped by the pick-up body. With
time, the fine pores in the pick-up
body become clogged with very fine
dirt particles. This reduces the
intake diameter and fuel can no
longer be delivered in sufficient
quantities.

Always check the fuel tank and pick-
up body first if problems develop in
the fuel supply.

1

5904RA435 TG

– Troubleshooting,

Clean the fuel tank if necessary.

– Open the filler cap and drain the

tank.

– Fill a little clean gasoline into the

tank, close the tank and shake it
thoroughly.

– Reopen the tank and empty it.

– Ensure that the fuel is disposed

of correctly and without harming
the environment,

– Open the filler cap

:

Use hook 5910 893 8800 to pull
the pickup body (1) out of the fuel
tank

Take care not to overextend the fuel
hose.

:

Pull off pickup body (1) and
examine it, replace if necessary

– Reassemble parts in reverse

order

1

5904RA436 TG

«
...
107
108
109
110
111
...
»

Summary of Contents for FS 240







































































































































Reviews:

No comments

Related manuals for FS 240

Brand: Racing Pages: 10

Brand: RASOR Pages: 15

Brand: Officezone Pages: 6

Brand: VITO GARDEN Pages: 20

Brand: Rockwell Pages: 20

SRM-2100 - PARTS CATALOG 6-95

Brand: Echo Pages: 18

Brand: Echo Pages: 64

Brand: UnionSpecial Pages: 18

Brand: Inter Laser Pages: 50

Brand: BOSTON WEATHERHEAD Pages: 8

Brand: Nemco Pages: 3

Brand: Toro Pages: 20

Brand: Stihl Pages: 104

Brand: FangLing Pages: 147

Brand: Gardeo Pages: 83

Brand: Gartner Pages: 56

Brand: RASOR Pages: 15

Brand: Makita Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands