Stihl FC 75 Service Manual Download Page 44

Page: 44 / 70

FC 75, FC 85, FH 75, FS 75, FS 80, FS 85, HL 75, KM 85, KW 85

– Wash the foam filter element in a

standard commercial solvent-
based degreasant containing no
chlorinated or halogenated
hydrocarbons and dry,

12.

– Replace the felt filter. As a

temporary measure, knock the
filter out on the palm of your hand
or blow clear with compressed
air. Do not wash.

– Replace any damaged parts.

Install in the reverse sequence.

– Fit the foam element in the filter

cover.

Fit the felt element in the filter
housing ("INSIDE" must face
engine).

936RA158

Innen

INSIDE

FACE INTERNE

Make sure that the slot in the filter
cover engages the lug on the
filter housing (arrow).

936RA159

If you suspect a fault in the fuel
system,

4.3

In the case of problems with the
carburetor or fuel supply system,
also check and clean or replace the
tank vent,

9.5.

The carburetor can be tested for
leaks with the carburetor and
crankcase tester 1106 850 2905.

– Remove the shroud,

5.1

– Disconnect the fuel hose from the

carburetor’s elbow connector
(arrow).

936RA160

Push the fuel hose (1)
1110 141 8600 onto the
nipple (2) 0000 855 9200.

143RA172

Push the fuel hose with nipple
onto the carburetor’s elbow
connector (arrow).

936RA161

Connect the tester's pressure
hose to the nipple (arrow).

936RA162

Close the vent screw (1) on the
rubber bulb (2) and pump air into
the carburetor until the pressure
gauge (3) shows a reading of
approx. 0.8 bar.

936RA163

9.2

Carburetor

9.2.1

Leakage Test

Summary of Contents for FC 75







































































Search results

Summary of Contents for FC 75

Reviews:

Brands by name

Popular brands

Stihl FC 75, Service Manual

Search results

Summary of Contents for FC 75

Reviews:

Brands by name

Popular brands