background image

and be ejected at high speed. They may

cause serious injury to persons.

► Work only with an undamaged mowing head.

► Never use metal objects in place of the nylon

mowing lines.

► Observe and remain inside the wear limits.

► If you have any doubts, be sure to consult a

STIHL dealer.

4.6.4

Metal cutting attachment

The metal cutting attachment is in a safe condi‐

tion if the following points are observed:

Metal cutting attachment and mounting hard‐

ware are undamaged.

Metal cutting attachment is not warped.

Metal cutting attachment is properly mounted.

Metal cutting attachment is correctly sharp‐

ened.

Cutting edges of the metal cutting attachment

have no burrs.

The wear limits are not exceeded.

If a metal cutting attachment not manufactured

by STIHL is used, it must not be heavier,

thicker, of a different shape, of a lower quality,

or larger in diameter than the largest metal

cutting attachment approved by STIHL.

WARNING

■ If it is not in an safe condition, parts of the

metal cutting attachment may come off and be

thrown at high speed. They may cause serious

injury to persons.

► Never work with a damaged metal cutting

attachment or damaged mounting hardware.

► Sharpen the metal cutting attachment cor‐

rectly.

► Deburr the cutting edges with a file.

► Have the metal cutting attachment balanced

by a STIHL servicing dealer.

► Observe and remain inside the wear limits.

► Use a metal cutting attachment specified in

these instructions for use.

► If you have any doubts, be sure to consult a

STIHL dealer.

4.7

Fuel Mixture and Refueling

WARNING

■ This trimmer requires a fuel mixture of gaso‐

line and two-stroke engine oil. Fuel mixture

and gasoline are extremely flammable. If fuel

mixture or gasoline make contact with open

fire or hot objects, they can cause a fire or

explosion. This can result in serious or fatal

injuries and damage to property.

► Protect fuel mixture and gasoline from heat

and fire.

► Do not spill fuel mixture and gasoline.

► If fuel has been spilled: Wipe up the fuel with

a cloth and do not attempt to start the engine

until all parts of the trimmer and the area

around it are dry.

► Do not smoke.

► Never refuel near a fire.

► Shut off the engine and allow it to cool down

before refueling.

► Start the engine at least 3 meters from the

fueling spot, outdoors only.

■ Inhaling fuel fumes and gasoline fumes can

have toxic effects.

► Avoid inhaling fuel fumes or gasoline fumes.

► Refuel in a well-ventilated location.

■ The trimmer becomes hot during operation.

The fuel expands and excess pressure can

build up in the tank. Fuel can escape as a

spray when the fuel tank cap is opened. The

escaping fuel can ignite. This can result in

serious injuries.

► Allow the trimmer to cool down first and then

open the tank cap carefully.

■ Clothing that has been in contact with fuel or

gasoline is more easily flammable. This can

result in serious or fatal injuries and damage

to property.

► If your clothing comes into contact with fuel

or gasoline: Change your clothing.

■ Fuel mix, gasoline and two-stroke engine oil

can harm the environment.

► Do not spill fuel, gasoline or two-stroke

engine oil.

► Dispose of fuel mix, gasoline and two-stroke

engine oil in accordance with local regula‐

tions and environmental requirements.

■ Fuel, gasoline or two-stroke engine oil can

cause irritation if they come into direct contact

with the skin or eyes.

► Avoid contact with fuel, gasoline and two-

stroke engine oil.

► In case of contact with the skin: Wash affec‐

ted areas with plenty of water and soap.

► In case of contact with the eyes: Rinse eyes

with plenty of water for at least 15 minutes

and seek medical advice.

■ The trimmer’s ignition system produces

sparks. Unconfined sparks may cause a fire or

an explosion in an easily combustible or explo‐

sive environment. This can result in serious or

fatal injuries and damage to property.

► Use the spark plugs described in this instruc‐

tion manual.

► Insert and tighten down the spark plug.

English

4 Safety Precautions

8

0458-856-0121-A. VA0.B21.

Summary of Contents for 561 C-M





























Reviews: