25
ENGLISH
EN
5 USING THE MACHINE
5.1
GENERAL
Never start the engine until all the above measures under
‘ASSEMBLY’ have been carried out.
Never use the snow thrower without first reading
and understanding the enclosed instructions and
all the warning and instruction stickers on the
snow thrower and in these instructions.
Always wear protective goggles or a visor during
use, maintenance and service.
5.2
BEFORE STARTING
The connection cable and its plugs must be fault
free and approved for outdoor use.
The connection cable may only be connected to
power sockets equipped with an earth leakage cir-
cuit breaker with a trip current of max. 30 mA.
The connection cable must be suspended on the ca-
ble support. Otherwise there is a risk of damage
alongside the plug which is potentially life-threat-
ening.
Connect the snow thrower with the electric cable from the
property’s power socket.
Suspend the cable on the cable support (1:B) and connect to
the connector (1:J).
5.3
START
Start the motor and the auger as described below.
1. Lean the snow thrower back slightly so that the auger is
raised a little above the ground.
2. Press in and hold the button (1:K) . Squeeze the handle
(1:A).
3. Release the ignition lock, lower the auger towards the
ground and start to clear the snow.
5.4
SAFETY TEST
After starting
and
before use
of the machine, it is essential
to perform the safety test below.
If the unit fails to operate as described,
DO NOT
operate it.
In this case, contact an authorised workshop for repair.
Auger test
Release the starting handle. The motor and the auger should
stop immediately
5.5
STOP
Stop the motor and the auger by releasing the starting handle
(1:A).
5.6
SNOW CLEARANCE
See fig. 1.
Never aim the snow at bystanders.
Always stop the engine before unclogging.
Always wear eye protection when operating the
snow thrower.
If the auger is blocked, never try to keep the motor
engaged for more than 20 seconds. Extensive en-
gagement will damage the motor.
1. Start the motor as described above and check the ejection
distance and direction.
2. If necessary, stop the motor and adjust the deflector (1:I).
Upwards gives a longer throwing distance and
downwards gives a shorter throwing distance. Lock the
deflector in position using the knob (1:E).
3. If necessary, stop the motor and adjust the discharge
chute (1:H) with the lever (1:F) so that the snow is ejected
in the desired direction.
4. Stop working by releasing the starting handle (1:A).
The snow thrower is propelled automatically with the aid of
the auger. To facilitate propulsion, raise the handlebar a little.
Do not push the snow thrower.
5.7
OPERATING TIPS
1. Clear away the snow immediately after snowfall.
2. For complete snow clearance, slightly overlap each
clearance pass.
3. If possible, discharge the snow downwind.
4. In strong wind, lower the deflector to direct the
discharged snow close to the ground, where it is less
likely to blow into unwanted areas.
5. For safety and to prevent damage to the snow thrower,
keep the area to be cleared free of stones, toys and other
foreign objects.
6. The snow thrower’s capacity depends on the depth and
density of the snow. Learn how the snow thrower works
in different snow conditions.
5.7.1
Dry and normal snow
Snow up to 20 cm deep can be removed quickly and easily
by clearing at an even speed. Plan for downwind discharge of
the snow.
5.7.2
Wet, packed snow
Drive slowly forward. Avoid to use the scraping blade to
remove remaining packen snow and ice. Hoeing will lead to
fatigue failure in the auger housing.
5.8
AFTER USE
The snow thrower must never be rinsed with wa-
ter. Risk of damage to the electrical system and
risk of electric shocks.
1. Stop the motor.
2. Disconnect the electric cable from the snow thrower and
the property’s power socket.
3. Allow the snow thrower to cool for 30 minutes.
4. Clean the inside and outside of the snow thrower with a
suitable brush.
5. Check that there are no damaged or loose parts. Repair/
replace parts if necessary.
