manualshive.com logo in svg

Stid ultrys, User Manual

Share
Download
Stid ultrys User Manual Download Page 91

 

 

 

91 

 

SPECTRE NANO READ ONLY  

© STid 

–

 MU_ULTRYS_V3.0.1_EN 

 Identification modes and communication ranges 

Card

 

 

Works by presenting the smartphone in front of the reader (like a badge). 

 

Contact: the smartphone must be in contact with the reader 
Up to 0.2m: smartphone must be in an area of 0.2m around the reader 
Up to 0.3m: smartphone must be in an area of 0.3m around the reader 

Up to 0.5m: smartphone must be in an area of 0.5m around the reader 
 

Bluetooth

®

 communication activation by sensor / ground loup 

 

 

 
Up to 1m: Smartphone must be in an area of 1m around the reader

 

Up to 2m: Smartphone must be in an area of 2m around the reader 
Up to 3m: Smartphone must be in an area of 3m around the reader 

Up to 4m: Smartphone must be in an area of 4m around the reader 
Up to 5m: Smartphone must be in an area of 5m around the reader 
 

TapTap 

 

 

By tapping your smartphone twice in your pocket. 

   

 

Up to 3m 

Up to 5m 
Up to 10m 
Up to 15m 

 

Hands-free 

 

 

Works without any user action. 

 

Up to 3m 

Up to 5m 
Up to 10m 

 

 
 

 

Remote 

 

 

Works remotely. The phone becomes your remote control. You can display up to 

two buttons per virtual badge. 

 

Up to 5m 

Up to 10m 
Up to 15m 

Up to 20m 
 
Remote control button active: If the "Remote" identification mode has been 
activated, allows you to associate the current configuration with the Remote 1 or 
Remote 2 button. 

Possibility to use the fields to name the buttons. 

 

 

 

 

a 

Summary of Contents for ultrys










































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands