st
eut
e T
echnol
ogies GmbH & Co. K
G
Brück
ens
tr
aße 91, 32584 Löhne, Germany
, www
.s
teut
e.c
om
//
RF Rx SW868/SW915/SW917/SW922-4W 24VAC/DC
4 / 28
Montage- und Anschlussanleitung / Funkempfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
Istruzioni di montaggio e collegamento / Ricevitore wireless
Instruções de montagem e instalação / Receptor sem fio
Инструкция по монтажу и подключению / Радио-приемник
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer. In case
of doubt, the German language version of these instructions shall
prevail.
Scope of delivery
1 device, 1 mounting and wiring instructions, carton.
Intended use
The four channel radio receiver is used to switch electrical loads via
radio transmission. The transmitters must conform to the steute Wire-
less protocol of the LR and ULR modules. The output of the receiver
can be switched by a maximum of 40 transmitters. Therefore, each
transmitter must be taught in once.
Mounting and wiring
The wireless range depends heavily on the local conditions. Conductive
materials may strongly affect the radio signal. This also includes thin
foils, e.g. aluminium laminations on insulation materials.
Antenna
Use suitable antennas only:
Device
Antenna
Mat. No.
SW868/922
Antenna with cable and SMA
plug-in connector
1188958
SW915/917
Antenna with cable and SMA
plug-in connector
1188987
Mount the antenna on a metal plate. The metal plate serves as an
HF counterweight. Minimum size of metal plate: 250 x 250 mm. Note
minimum sideways distance to nearest wall or disturbance source:
>300 mm. Do not bend or clamp the cable. Minimum bending range of
cable: >25 mm.
English
Assignment of the place of use:
Device type
Place of use
according to
SW868
EU
2014/53/EU (RED)
SW915
USA
Canada
Mexico
FCC
IC
IFT
SW917
Brazil
ANATEL
SW922
Japan
ARIB STD-T108
Assignment of radio frequency:
Device type
Radio frequency
SW868
868.3 MHz
SW915
915.0 MHz
SW917
917.0 MHz
SW922
916.5 MHz
Design of wireless range
The radio signal is attenuated on the way from the transmitter to
the receiver. In addition, the radio signal is attenuated/influenced by
obstacles. The degree of attenuation depends on the material of the
obstacle. The following tables serve as a guide.
Penetration of radio signals:
Material
Penetration
wood, gypsum, glas uncoated
90…100 %
brick stone, press boards
65…95 %
armoured concrete
10…90 %
metal, aluminium lamination, water
0…10 %
Typical ranges:
Place of use
Wireless range (approx.)
in free field (SW868/915/917 LR)
450 m
in free field (SW868/915/917 ULR)
700 m
in free field (SW922 LR)
150 m
in free field (SW922 ULR)
230 m
indoors (SW868/915/917 LR)
40 m
indoors (SW868/915/917 ULR)
50 m
indoors (SW922 LR)
20 m
indoors (SW922 ULR)
25 m
To get the maximum range: use the specified antennas. With other an-
tennas, the maximum range may differ.
