DIGITAL LINE
DIGITAL LINE
9K EQ
DIGITAL LINE
DIGITAL LINE
SET/2014 - R1
SPECIFICATIONS
USER’S GUIDE
Note:
If only the RED LED blinks (BLUE LED OFF), turn on the device with the volume of CD/MP3-player down. If
the problem persists, please contact us.
LEDS INDICATORS (TOP OF THE AMPLIFIER)
SYSTEM TROUBLESHOOTING
- RED LED (PROT) illuminates only when
there is a problem in the functioning of
the device.
- RED LED (CLIP) flashes when
the amplifier output begin to
distort the sound.
- BLUE LED (POWER)
lights when the power
is on.
If a problem occurs, the amplifier will turn off and the LED RED / PROT flashes. As the problem occurred, the RED
LED / PROT will flash a number of times. So we have a diagnosis according to the table below:
NOT TURN ON:
- The cables are not properly connected (terminals +BATT, GND and REM). Make sure that all
connections are mechanical and electrical contact.
- Fuses / breakers (external) are defective or burned. Pay attention to the correct value of the new fuse!
NO SOUND:
- The cables of the speakers or RCA plugs are not connected correctly.
- Check that the LEVEL control is not in the minimum.
NO SOUND/PROTECTION RED LED FLASHING:
- See diagnosis UP (SYSTEM TROUBLESHOOTING).
- The speakers or cables defectives thus check the speakers, cables and connections.
POOR SOUND QUALITY (DISTORTION):
- The speakers are overloaded, therefore decrease the level and redo the gain setting (See item 4 /
OVERVIEW).
WEAK BASS:
- Cables speakers (+) and (-) are reversed, speaker out of phase (see Section 8 / overview).
MOTOR NOISE, HORN, SIGNAL LIGHT, ETC:
- Use suppressive cables in ignition candles.
- Use capacitors in the alternator, horn and ignition.
- Pass the RCA cable away from any other cable, because it is more sensitive to interference.
- Connect to power (+12 V) to separate the sound system. Use a fuse to 30 cm from the battery for
protection.
- Make a good grounding of the amplifier. To do this removes the paint from the chassis of the vehicle at
the desired point. Screw the cable using a ground terminal. To protect from oxidation, insulate with
paint.
- Do not loop the ground wire. Avoid using several ground wires. Prefer a star connection, with all the
ground wires aside from a single point.
WHAT TO DO IN CASE OF PROBLEMS
www.stetsom.com - [email protected]
MODEL:
9K EQ – 2 OHMS
9K EQ – 1 OHM
Channels:
1
1
Power @ 13.8V Mono 1 Ohm:
-
10.000 Watts RMS
Power @ 13.8V Mono 2 Ohms:
10.100 Watts RMS
6.400 Watts RMS
Power @ 13.8V Mono 4 Ohms:
6.250 Watts RMS
3.900 Watts RMS
Power @ 12.6V Mono 1 Ohm:
-
9.000 Watts RMS
Power @ 12.6V Mono 2 Ohms:
9.000 Watts RMS
5.400 Watts RMS
Power @ 12.6V Mono 4 Ohms:
5.150 Watts RMS
3.200 Watts RMS
Minimum Work Impedance:
2 OHMS
1 OHM
Input Impedance:
27K OHMS
25K OHMS
Minimum Input Sensitivity:
0,2V
0,2V
Total Harmonic Distrotion:
< 0,9 % THD
< 0,9 % THD
Signal to Noise:
> 90 dB
> 90 dB
Frequency Resp. (-3dB) @ 8 Ohms:
10 Hz a 15 KHz
10 Hz a 15 KHz
Crossover Low Pass:
50 Hz a 15 KHz
50 Hz a 15 KHz
Crossover High Pass:
10 Hz a 700 Hz
10 Hz a 700 Hz
EQ - BASS @ 45Hz:
±10dB
±10dB
EQ - MID BASS @ 270 Hz:
±10dB
±10dB
EQ - MID HIGH @ 2KHz:
±10dB
±10dB
Over CLIP:
15% + Potência
15% + Potência
Power Supply:
9,5 a 15 V
9,5 a 15 V
Consumption Music Signal (12,6V):
6,1 a 400 A
6,7 a 445 A
Consumption BASS Signal (12,6V):
6,1 a 800 A
6,7 a 890 A
Dimensions (A x L x C) mm:
75 x 310 x 510
75 x 310 x 510
Weight Kg:
7,4
7,4
