Steris P920011-649 Operator'S Manual Download Page 94

Page: 94 / 168

4-49

Processing Instructions

Operator Manual

920011-649

When Abort sequence is completed, display shows:

and printer records:

==========================
CYCLE CANCEL HH:MM:SS: XX
==========================

IMPORTANT: If a recurring alarm occurs that prevents the Abort
sequence from being completed, call STERIS.

4.13.2 Maintenance Due

Faults

There are four

MAINTENANCE DUE

alarms indicating when specific

routine maintenance needs to be performed on the processor.
1. When a

MAINTENANCE DUE

alarm occurs, display shows:

alternating with:

and printer records:

=========================
HH:MM:SS XM

MM-DD-YY

=========================
= MAINTENANCE XX

=========================

2. Press

ALARM REPLY

touch pad to acknowledge alarm. Display

shows:

NOTE:

For MAINTENANCE DUE alarms, refer to

, for a detailed listing of

maintenance alarms. If maintenance is not performed on
processor, MAINTENANCE DUE alarm will be displayed every
24 hours as long as maintenance is not performed and counter is
not reset.

CYCLE CANCELLED

READY TO UNLOAD

MAINTENANCE DUE

MAINTENANCE XX

SEE CHART

READY

MM-DD-YY HH:MM XM

Summary of Contents for P920011-649









































































































































































Search results

Summary of Contents for P920011-649

Reviews:

Brands by name

Popular brands

Steris P920011-649, Operator'S Manual

Search results

Summary of Contents for P920011-649

Reviews:

Brands by name

Popular brands