Steris P920011-649 Operator'S Manual Download Page 27

Page: 27 / 168

2-2

920011-649

Operator Manual

Installation Verification

2.1.4 Seismic Anchorage

System (Accessory)

A seismic anchorage system (accessory; based on California

requirements) is available for high-risk seismic zones.

2.2 Installation

Verification

An equipment drawing (920-011-656), showing all of the utility and

space requirements, was shipped after the order for this equipment

was received. The clearance space specified on the equipment

drawing is necessary for proper installation, operation and

maintenance.

Uncrating/Installation Instructions

(P920011-648) are

provided with the processor. If these documents are missing or

misplaced, contact STERIS and provide the serial number of the

processor. Replacement copies will be shipped promptly.
After installing the equipment according to the

Uncrating/Installation

Instructions

, complete the following checklist to help ensure

complete and correct installation, or contact STERIS to schedule a

service technician to test your installation and demonstrate proper

equipment operation.

�

Shutoff valves (not provided by STERIS), capable of being

closed for maintenance purposes, are installed on the water

lines. Shutoff valves must be compliant with the local

occupational health and safety regulations, as well as electric

and plumbing codes.

�

Disconnect switches (not provided by STERIS), capable of being

locked in OFF position for maintenance purposes, are installed

in electrical supply lines near the processor. Disconnect

switches must be compliant with local occupational health and

safety regulations, as well as electric codes.

NOTE: If processor is installed next to other equipment, shutoff
valves and disconnect switches should be located so service can
be shut off to one piece of equipment at a time.

�

Processor is positioned, as shown on equipment drawing, with

required clearance space and in relation to building supply

lines.

�

Processor is level. Adjust leveling casters if necessary.

�

Dual Pre-Filter and Pressure Regulator Assembly (required

accessory), pressure gauge and manual ball valve (with dual

pre-filter kit) are installed as specified on equipment drawing.

�

Measure building hot and cold water supply pressures at shutoff

valves. Pressure readings must be within specifications on

equipment drawing.

•

If water pressure is lower than equipment drawing
specifications:

A water pump with a pressurized tank (not

provided by STERIS) is needed to increase water pressure.

•

If water pressure is higher than equipment drawing
specifications:

Dual Pre-Filter and Pressure Regulator

Assembly (required accessory) can be adjusted to regulate

high water pressure to specified pressure.

Summary of Contents for P920011-649









































































































































































Search results

Summary of Contents for P920011-649

Reviews:

Brands by name

Popular brands

Steris P920011-649, Operator'S Manual

Search results

Summary of Contents for P920011-649

Reviews:

Brands by name

Popular brands