manualshive.com logo in svg

Steris AMSCO 400 Series, Operator'S Manual

Share
Download
Steris AMSCO 400 Series Operator'S Manual Download Page 7

v

Introduction

Operator Manual

P129394-020

Table 3.  Test Cycles

 

Gravity Cycle

270°F 

(132°C)

15 Minutes

30 Minutes

Double-wrapped instrument trays. 
Maximum weight per tray, 25 lb 
(11.3 kg)

ST-8:2008

Gravity Cycle

250°F 

(121°C)

30 Minutes

30 Minutes

ST-8:2008

Gravity Cycle

270°F 

(132°C)

25 Minutes

15 Minutes Fabric Packs

ST-8:2008

Immediate Use 
Gravity Cycle

270°F 

(132°C)

3 Minutes

1 Minute

Unwrapped instrument tray containing 
a single instrument; or multiple 
unwrapped instrument trays, non-
porous load. Maximum weight per 
tray, 25 lb (11.3 kg)

ST-8:2008

Immediate Use 
Gravity Cycle

270°F 

(132°C)

10 Minutes

1 Minute

ST-8:2008

Liquid Cycle

**

250°F 

(121°C)

45 Minutes

N/A

Refer to 

Table 5 (page vi)

 for 

recommended quantities

ST-8:2008

6. Leak Test

***

 

N/A

N/A

N/A

None

ST-8:2008

7. DART Test**

270°F 

(132°C)

3-1/2 

Minutes

1 Minute

Dart or Bowie-Dick Test Pack

ST-8:2008

8. DART Warm-up**

270°F 

(132°C)

3 Minutes

1 Minute

None

N/A

*

Dry time can be reduced to 5 minutes for a single fabric pack.

** The liquid cycle is for non-patient contact use only.
*** Not adjustable.

Test Cycles for 
All Units: 

Sterilize 
Temp.

Sterilize 
Time 

Dry 
Time 

Recommended Load

Validation 
Standard

Leak Test

*

 

*

Not adjustable.

N/A

N/A

N/A

None

ST-8:2008

DART Test*

270°F (132°C)

3-1/2 

Minutes

1 Minute DART or Bowie-Dick Test Pack

ST-8:2008

DART Warm-up*

270°F (132°C)

3 Minutes

1 Minute None

N/A

Table 2. AMSCO 400 Series SFPP Sterilizer Cycles (Continued)

Cycles:

Sterilize 
Temp.

Sterilize 
Time

Dry 
Time

Recommended Load 

Refer to 

Table 4 (page vi)

 for 

Recommended Quantities

Validation 

Standard

Summary of Contents for AMSCO 400 Series















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands