manualshive.com logo in svg

Steris AMSCO 400 Series, Operator'S Manual

Share
Download
Steris AMSCO 400 Series Operator'S Manual Download Page 158

9-16

P129394-020

Operator Manual

Troubleshooting

Alarm

Description

Screen with Service Instructions

Atmospheric Pressure

Alarm (Continued)

Alarm

Description

Screen with Operator Instructions

9.3.4  Too Long To

Close Door

Occurs if door switch 
does not make contact 
within allotted time.

Screen with Service Instructions

STATUS . .  SERVICE INFORMATION:

270

ATMOSPHERIC PRESSURE ALARM

-> THE ATMOSPHERIC PRESSURE IS 

GREATER THAN 1 PSI FROM THE
CALIBRATED ATMOSPHERIC PRESSURE

CAUSES AND CORRECTIONS:
1. THE STERILIZER IS AT A HIGHER

ALTITUDE THEN WHERE IT WAS
ORIGINALLY CALIBRATED (FACTORY)
-> SET ALTITUDE

2. CONTROL OUT OF CALIBRATION

-> RECALIBRATE (CONTACT QUALIFIED 
   SERVICE PERSON)

3. LOOSE CONNECTION IN TRANSDUCER WIRING

-> REPAIR

4. TRANSDUCER FAILED

-> REPLACE
-> RECALIBRATE

PAPER

FEED

EXIT

CLEAR
ALARM

STATUS . .  ALARM!

239

TOO LONG TO CLOSE DOOR

CHAMBER:   00.0 F    0.0 psig

STERILIZER WILL:

•

REMAIN IN ALARM CONDITION UNTIL
DOOR IS CLOSED

OPERAT0R INSTRUCTIONS:
1. SILENCE ALARM
2. CHECK DOOR FOR OBSTRUCTION

-> REMOVE OBSTRUCTION AND CLOSE DOOR

3. IF DOOR WILL NOT CLOSE, CALL SERVICE

SERVICE

HELP

STATUS

PRINT

SILENCE

ALARM

PAPER

FEED

STATUS . .  SERVICE INFORMATION:

240

TOO LONG TO CLOSE DOOR

-> DOOR SWITCH DID NOT MAKE IN ALLOTTED TIME

CAUSES AND CORRECTIONS:
1. DOOR SWITCH MALFUNCTION

-> CHECK LS1 (LS2) CONNECTIONS
-> READJUST LS1 (LS2)
-> REPAIR LS1 (LS2)

2. POWER DOOR MECHANISM FAILURE

-> REPAIR MECHANISM
-> REPLACE MOTOR

PAPER

FEED

EXIT

CLEAR
ALARM

Summary of Contents for AMSCO 400 Series















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands