manualshive.com logo in svg

StereoVision FS4000, Instruction Manual, Page: 18 / 24

Share
Download
StereoVision FS4000 Instruction Manual Download Page 18

       

Fire Control Panel FS4000 

- right indicator

 (if no other lines are set to test condition). 

12. Delay of outputs

12.1. Description 

 The Fire control Panel registers the time delayof the outputs after manual operation for setting 

the appropriate value.The time delay is set by a combination of 1

st 

 2

nd

and 3

rd  

discharge of DIP switch 

(pos.3, Figure 1) (Table 4) and can be 0, 1, 2, 3, 4, 5, 6 or 7 minutes. At time delay set to ''0'' – the 
outputs are activated immediately after the Fire control panel enters Fire condition. 
         Time delay setting is performed by moving the first three discharges of microswitchers (pos 3, 
fig .1) in the following tables :    

Table 5 

DIP

0

minutes 

1 

minute 

2 

minutes 

3 

minutes 

4 

minutes 

5 

minutes 

6 

minutes 

7 

minutes 

1  OFF OFF OFF OFF  ON  ON  ON  ON 
2  OFF OFF ON  ON OFF OFF ON ON 
3  OFF ON OFF ON OFF ON OFF ON 

When the time delay is set to 

≠

 0, the indicator is illuminated with continuous yellow light 

13. User configuration of the outputs

The Fire Controll Panel provides the option for inserting combinations for outputs activation .8 
constant combinations are set. An operating combination shall be chosen by 6

th

, 7

th

, and 8

th

 discharge 

DIP switch (pos.3, fig.1).  

Possible combinations are given in Table 6. 

 Table 6 

Rel 1 

Rel 2 

Out 1 

Out 2 

1 

DIP

position

6

OFF

7

OFF

8

OFF

Switches On 
immediately 

Switches On 
with time delay 

Switches On 
with time 
delay 

Switches On 
with time 
delay 

2 

DIP

position

6

OFF

7

OFF

8

ON

Switches On 
immediately 

Switches On 
immediately 

Switches On 
with time 
delay 

Switches On 
with time 
delay 

3 

DIP

position

6

OFF

7

ON

8

OFF

Switches On 
with time delay 

Switches On 
with time delay 

Switches On 
with time 
delay 

Switches On 
with time 
delay 

4 

DIP

position

6

OFF

7

ON

8

ON

Switches On 
with time delay 

Switches On 
with time delay 

Switches On 
immediately 

Switches On 
immediately 

5 

DIP

position

6

ON

7

OFF

8

OFF

Switches On 
only in Fire 
condition of line 
1 

Switches On 
only in Fire 
condition of 
line 2 

Switches On 
with time 
delay 

Switches On 
with time 
delay 

Instruction manual 

          Page 18 

Revision 4/02.11 

of 24 

Summary of Contents for FS4000

























Reviews:

No comments