STEINWAY LYNGDORF P300 2.1 Owner'S Manual Download | Manualshive

Page: 25 / 35

background image

Steinway & Sons P300 2.1 Owner’s manual

25

OSD info level

Choose the level of information to show on the OSD.

Trigger In Setup

Allows you to set up the system so that it can be switched on via an external device in the system.

Trigger Out Setup

Allows you to set up the system so that the Model P300 2.1 can control other devices in the system.

Network Configuration

Change the network mode to “Manual” or “Automatic”.
For more info, see the Network Setup chapter.

Streaming Setup

Configure streaming player setup.
Streaming players can control volume: Set to Off or On.
Streaming players can change input source: Set to Off or On.
Streaming players can power on the device from standby mode: Set to Off or On.

«
...
23
24
25
26
27
...
»

Summary of Contents for P300 2.1




































Reviews:

No comments

Related manuals for P300 2.1

Brand: Oemtools Pages: 4

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: UFO Pages: 16

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

Brand: YASKAWA Pages: 1166

Brand: ubicquia Pages: 4

ResQCRP ResQPUMP ACD-CPR

Brand: Advanced Circulatory Pages: 2

Big Wheel RN1 Series

Brand: Osborne Pages: 8

Brand: impact Pages: 8

Brand: TOTAL10 Pages: 16

Brand: EcoNet Pages: 83

Brand: Vision & Control Pages: 32

Brand: Huvitz Pages: 97

Brand: Midstream Pages: 13

Brand: Preventice Solutions Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands