manualshive.com logo in svg

Steinsvik Orbit-200, User Manual

Share
Download
Steinsvik Orbit-200 User Manual Download Page 18

 

18 

 

4.13  Surveillance camera 

 
Steinsvik also supplies several surveillance cameras meant for surveillance at the barge. The Orbit-351 
and the Orbit-310 are reliable cameras that provides good visibility on the facility and specific parts of 
the facility.  
 

4.13.1  Orbit-310 

With careful installation of the Orbit-310, you will gain maximum advantage of the camera. The camera 
can easily be controlled with a gamepad and has an excellent zoom. In addition to manual control, the 
camera can be pre-set to fixed positions via the software. The software allows for control of the camera 
with only a keystroke where you can position the camera from the spreader in the outer most edge of 
the cage, to the distribution valve at the barge. The Orbit-310 must 

only

 be installed at the barge 

– for 

cage installation use Orbit-200/210.  
    
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Table 11 Specifications Orbit-310 

Specifications 

Video signal 

Video over IP 

Resolution  

Full HD 1080p 

Sensor type 

Colour BSI CMOS 

Zoom 

30 x optic, 12 x digital  

Lens opening  

F 1.6 

Light sensitivity 

0,0015 lux 

– 50 IRE 

Weight 

10,5 kg (incl. cable) 

IP degree 

IP67 

Temperature range 

-10°C - +50°C 

Effect 

11-13 VDC, 24 VAC or PoE +30W 

Material 

Aluminium, PC and POM 

Range of motion  

360° (horizontal), 90° (vertical) 

Focus 

Auto 

Cable length  

30 M 

Pan/tilt 

Manual and Auto 

Figure 13 Orbit-310

 

Summary of Contents for Orbit-200















































Reviews:

No comments

Brands by name

Popular brands

Load more brands