SteelMax SBM-500 Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 44

background image

SBM-500

SBM-

500 Operator’s Manual

8

20. Do not use near flammable materials or in explosive environments.

21. Always use the feed wheel during work.

22. Use eye protection, ear protection, gloves, and protective clothing. Do not use

loose clothing.

23. Do not touch chips or moving parts. Do not let anything catch in moving parts.

Do not put hands under the feed wheel.

24. After each use, clean the machine and the milling head with a cotton cloth and no

chemical agents. Do not remove chips with bare hands.

25. Maintain the machine and install/remove parts and tools only after you unplug the

machine from the power source.

26. Repair only in a service center appointed by the seller.

27. If the machine is wet or has any damage, stop the work and promptly send the

machine to the service center for check and repair.

28. Do not leave the machine when it operates.

29. If you are not going to use the machine for an extended period, put anti-corrosion

material on the steel parts.

«
...
6
7
8
9
10
...
»

Summary of Contents for SBM-500













































Reviews:

No comments

Related manuals for SBM-500

Brand: Taylor Pages: 70

Brand: Raith Pages: 26

Brand: Kane Pages: 16

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

FlexDraper FD2 Series

Brand: MacDon Pages: 2

OXYGEN PRO MINI

Brand: M-Audio Pages: 56

Brand: Ocean Sonics Pages: 45

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Brand: Vahle Pages: 36

Brand: Vahle Pages: 20

Brand: Vacon Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands