06800 - EngineEAR® II - STEELMAN
INSTRUCTION MANUAL
SPECIFICATIONS
06800
PART NO.
DESCRIPTION
EngineEAR
®
II
EngineEAR
®
II
JS Products, Inc. • 5440 S. Procyon St. • Las Vegas, NV 89118
Phone: 702-362-7011 • Fax: 775-898-8773 • www.steelmantools.com
LIMITED WARRANTY
STEELMAN
®
JS Products, Inc. has carefully examined each product at the time of
manufacturing and warrants workmanship at the time of shipment. This warranty applies only
to the original consumer/purchaser and is not valid if the product is misused, or if accidental
damages occur.
STEELMAN
®
JS Products, Inc. assumes no direct or indirect liability for
incidental or consequential damages resulting from the use of its products. This warranty
commences on the date of the original consumer purchase, and extends for 90 Days
thereafter.
In the event of a defect or malfunction of a product, wherein repair or replacement should be
necessary, call the Customer Service Department at 1-800-255-7011 for complete
instructions on how to return the product for warranty repair or replacement. The original
consumer/purchaser must provide a copy of the Bill of Sale or Invoice showing the date on
which the purchase was made. After the (ninety) 90 Day Period,
STEELMAN
®
JS Products,
Inc. will charge a service charge for all parts and labor. Inbound and outbound freight will be
paid by the consumer/purchaser.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Additionally, some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation may not apply
to you.
This warranty gives specific legal rights, and there may be other rights which vary from state
to state.
OPERATING INFORMATION
ADVANCED ELECTRONIC LISTENING TOOL
Rev: 05/03/11
FRONT
BACK
COLOR SPECIFICATION:
1-COLOR
MATERIAL SPECIFICATION:
80 lb. Gloss Text
SIZE SPECIFICATION:
5.50"H x 8.50" W - FRONT AND BACK
Black =
100% Black
5) Place sensing tip flush on housing surface of suspect problem parts. By keeping
the sensing tip flush against the suspect part, outside noises are blocked. Use the
metal probe when working on hot or difficult to reach areas. The probe fits into the
EngineEar II microphone, senses the faintest vibrations and transmits very clear
sounds to the headphones.
6) Use the EngineEAR
®
II to detect bad bearings and bushings, noisy lifters, exhaust
manifold leaks, broken or chipped gear teeth. Is can also be used to pinpoint the
location of wind and water leaks around doors, windows and sunroofs.
NOTE:
EngineEAR
®
II electronically amplifies sound and will provide clear sound around
most parts of most automobiles and equipment. Occasional static interference
around the coil and distributor of some cars may occur.
WARNING:
Amplified noise levels: Avoid prolonged use at levels above 85dBA. Prolonged
exposure can cause personal injury.
1) Install 9-volt battery in EngineEAR
®
II control unit and turn top dial to battery check
position. The dB meter will indicate charge level battery test. Attach headphone plug
to the control unit.
2) Turn On/Off switch to “Off” position before putting on headphones. Place
headphones firmly over ears, then turn the switch to “dB range” setting with volume
on low. Slowly rotate the dB range selection dial.
3) Place the tool near the suspected source of the noise and turn the dB range dial
until the meter reads near the center zero scale marking. If the reading on the meter
is a +2 and the dB range is set to 80, the noise level is at 82 dB. After using the tool,
you will learn the various basic settings for different types and sources of engine and
vehicle noises. Increase volume control as needed to a comfortable sound level.
4) The high-low tone setting works similar to a treble/bass setting. Switch to the tone
most comfortable to your personal hearing.
CAUTION:
It is against many state
laws to operate a motor vehicle
while wearing headphones.
QTY
Description
KIT CONTENTS
Control Unit, dB Meter w/ Amp & Mic
Headphones
Rubber Sensor Tip
Metal Probe
1
1
1
1
06802
HD-6060N
65012
413
Part No.
How to Use:
