background image

Page 3

TABLE OF CONTENTS

INTRODUCTION

This user manual is intended for use by anyone working with this machine. It should be kept available

for immediate reference so that all operations can be performed with maximum efficiency and safety.

Do not attempt to perform maintenance or operate this machine until you have read and understand the

information contained in this manual.

The drawings, illustrations, photographs, and specifications in this user manual represent your machine

at time of print. However, changes may be made to your machine or this manual at any time with no

obligation to Steel City.

INTRODUCTION...........................................................................................................3

TABLE OF CONTENTS.................................................................................................3

WARRANTY ..................................................................................................................4

PRODUCT SPECIFICATIONS ......................................................................................5

GENERAL SAFETY ......................................................................................................6

PRODUCT SAFETY......................................................................................................8

ELECTRICAL AND GROUNDING INSTRUCTIONS.....................................................9

UNPACKING AND INVENTORY .................................................................................10

ASSEMBLY..................................................................................................................11

ADJUSTMENTS..........................................................................................................13

DIAGRAM....................................................................................................................16

PARTS LIST ................................................................................................................17

Summary of Contents for 40-660





















Reviews: