EN
ELECTRICAL
VACUUM PUMP
BVP130
USER MANUAL
1.1. OPERATING CONDITIONS
The maximum surrounding temperature for
normal use is +40°C, while the average tem-
perature during a 24-hour period must not
35 °C. The lowest allowed surrounding
temperature is -5 °C.
Normal room temperature is most suitable.
Surrounding air must be clean, relative
humidity must not exceed 50 % at the maximum
temperature of +40 °C. Higher relative humidity
is allowed with lower surrounding temperature
(e.g. 90 % at +20°C).
1. SAFETY INSTRUCTIONS AND
EXPLANATION OF OPERATION
1.2. SAFETY INSTRUCTIONS
a.) Choose the place for the device carefully.
The surface used for the device must be dry
and of normal temperature (not hot), and
must not be next to a heat source (heating
surface) or source of water.
b.) Check the USB charging cable, connectors,
adapter (which can be bought additionally)
and plug before connecting the device to the
adapter and the adapter to the plug (power
supply). If you observe any defect, contact
our repair service listed below.
c.) Use the device exclusively for the purposes
described in the instructions for use.
d.) If the USB charging cable is damaged, the
manufacturer, authorized repair service, or
similarly qualified personnel must replace it
to prevent any danger.
e.) This device can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capa-
bilities or lack of experience and knowledge
if they have been given supervision or in-
struction concerning use of the appliance
in a safe way and understand the hazards
involved.
f.) Children shall not play with the device. Clean-
ing and user maintenance shall not be made
by children without supervision.
g.) The warranty is void in the following cases:
• An unauthorised or unqualified person at
-
tempts to repair the device.
• The device is used for purposes other than
intended.
• Safety rules and instructions for use are
not followed.
h.) Never use the device in an explosive atmo-
sphere.
i.) Store the device in dry spaces at room tem-
perature.
When correctly connected and used in accor-
dance with the instructions, the device is not
dangerous.
Electrical components use low voltage and are
protected against dust.
Read the instructions for use thoroughly
before use.
The instructions for use should be stored next
to the device and always available during use.
Opening the device and accessing its interior by
a user is forbidden.
The manufacturer assumes no liability for dam-
age caused by incorrect use or by failure to
comply with the instructions.
1.4. REPAIR SERVICE
a.) Only qualified and authorised personnel may
perform repairs.
b.) Only experts that can assess the task at
hand and related risks, based on their tech-
nical education and knowledge of appropri-
ate standards, can perform repairs.
c.) Troubleshooting is performed by the manu-
facturer or an authorised representative.
d.) If possible, components that need to be
replaced are replaced with the original or
functionally identical spare parts.
1.5. GENERAL INFORMATION
The electrical vacuum pump BVP130 is a vacuum packing device. It is intended
to be used on Status vacuum containers, jug, lids, and stoppers thereby creating
vacuum and ensuring quality vacuum storage of food in a container, jug, bottle
or a jar.
The biggest advantages of vacuum storage are the following:
• it preserves vitamins, minerals, nutrients, and the aroma of foodstuffs,
• it protects food from the spread of mould and bacteria,
• it prolongs the shelf life of foodstuffs,
• food stored in vacuum containers can be refrigerated or frozen,
• it prevents the unpleasant mixing of odours in a refrigerator and freezer.
The use of the electric vacuum pump is simple and efficient. It allows you
to store food in a completely natural and healthier way. Food remains fresh
longer and you end up saving time and money.
Please read the user manual thoroughly before first use and follow the
instructions. Should any questions, opinions, or comments arise, feel free
to contact us by phone or mail.
This user manual is also available in electronic form at our website
www.status-innovations.eu/knowledge-base/user-manuals/.
1.6. PRODUCT SPECIFICATION
Dimensions
Width: 55 mm
Length: 55 mm
Height: 112 mm
Weight
0.2 kg
Material
PC ABS plastic, silicone
Rated voltage and current
3,7 V , Li-Ion, 800 mA
Adapter
(not included)
Input: 100-240 V~, 50-60 Hz
Output: 5 V , 800 mA
1.7. COMPONENTS AND DESCRIPTION
OF THE PRODUCT’S FUNCTIONING
The image below shows the BVP130 electric vacuum pump. It is easy
to use since all you have to do is place it on top of the silicone valve
and press the button .
Lights explanation:
• The indicator light alternates between red and green flashes during
operation.
• A short flash of the red light signals an empty battery and indicates
the pump needs to be charged.
• The pump is charged when the green light turns on.
The electric vacuum pump creates a preset vacuum pressure in a
container, jug, bottle, or a jar.
The most important functions and components are indicated with
numbers.
1. Button and colour indicator
2. The body of the vacuum pump
3. Silicone seal
4. USB power cable
a.) USB 2.0 and
b.) micro USB
5. Slot for the micro USB connector
2
5
1
4
4b
4a
3
2.1. GENERAL INSTRUCTIONS
a.) Upon removing the electric vacuum pump from its packaging
make sure that all the component parts are included and that the
device and all its component parts are fully operational. Take spe-
cial care to remove all the packaging bits from the seal.
b.) Make sure you read the user manual thoroughly before first use
and follow the instructions.
c.) The electric vacuum pump is designed for household use.
2.2. INSTRUCTIONS FOR USE
a.) The vacuum pump needs to be charged before first use.
b.) Vacuum pack by placing the vacuum pump on the valve at the
centre of the lid of a vacuum container, jug, or a vacuum stopper
and press lightly.
c.) Press button. The pump automatically sucks the air out of the
container, jug, or a bottle.
d.) The indicator light alternates between red and green flashes
during vacuum packing.
e.) The duration of vacuum packing depends on the size of the con-
tainer and the amount of food: vacuum will be created faster in a
smaller container than a larger one, and in a full container than
an empty one.
f.) The pump disengages automatically when the vacuum pressure
in a container reaches the preset value.
g.) The operation of the pump can be stopped at any time by pressing
the button .
h.) If the pump’s battery is empty, it will not power on upon pressing
button. The battery needs to be charged.
2.4. STORAGE OF THE PUMP
Store the pump in a dry space at room temperature, away from a
heat or water source. Due to its small size it is easy to carry and
suitable for use at home, on the go, or at work.
a.) Directive on the harmonisation of the laws of the Member States relating
to the making available on the market of electrical equipment designed for
use within certain voltage limits
LVD DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT AND OF
THE COUNCIL
b.) Directive on the harmonisation of the laws of the Member States relating
to electromagnetic compatibility (recast)
EMC DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF
THE COUNCIL
EU Declaration of conformity guarantees that the machine is
safe and has been inspected and tested to meet all the
requirements specified in the applicable standards, directives
and regulations.
EU Declaration of conformity for CE marking is located at the
seller and can be provided per customer’s request.
3. DECLARATION OF CONFORMITY
4. TROUBLESHOOTING
Problem:
Solution:
The pump does not
respond to pressing
the button .
• It is most likely that the pump’s battery is
empty. Charge the battery.
The pump does not
create vacuum in a
container, jug or in
a container closed
with a universal lid,
or the
vacuum does not
persist.
• Check if the lid of the vacuum container,
the seal, and the valve are positioned
correctly.
• Check if the silicone seal and the valve
of the container are clean and dry. If
necessary, remove the valve from the lid,
clean it, and reattach it.
The pump works
but it
does not create
vacuum in
a container.
• During the vacuum packing press the
pump in the dock surrounding the valve
in order to create a tight seal between
the pump and the area around the valve.
• Check if the lid of the vacuum container,
the silicone seal and the valve are positi-
oned correctly.
• Check if the silicone seal and the valve
of the container are clean and dry. If
necessary, remove the valve from the lid,
clean it, and reattach it.
The problems
encountered
cannot be solved.
• You must contact the repair service. The
manufacturer will assume responsibi-
lity only if you comply with instructions
and do not attempt to repair the device
yourself.
5. CORRECT DISPOSAL OF YOUR
VACUUM MACHINE
When the equipment or parts of the device are no longer fit for use they must
be disposed of at the industrial waste landfill in accordance with applicable
regulations:
• Directive on waste electrical and electronic equipment (WEEE)
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL
• Directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL
Environmentally hazardous components and parts that were built into the de-
vice have to be disposed of at specialized sites.
The symbol on the product or its packaging indicates that at the
end of its life, the product may not be treated as ordinary house-
hold waste and must be disposed of in accordance with your local
authority’s instructions and at properly designated sites. You can
also use an official WEEE collection service provider in accor
-
dance with directive 2012/19/EU.
Separate collection of individual components of EE equipment prevents
negative effects of environmental pollution and minimizes danger to human
health, which may occur as a result of improper product disposal. In addition,
it enables reuse and recovery of the material, thus saving energy and raw
materials. For detailed information on collecting, sorting, reuse and recycling
of the product contact the provider of WEEE collection services or the shop
where you bought the equipment.
This warranty is valid for
two years
from the date of purchase. Evidence of
original purchase is required for warranty services, so it is important to keep
your sales receipt.
This warranty only covers breakdown caused by electrical or mechanical fail-
ure. It does not cover damage caused by liquid entering the device or break-
down caused by failure to follow the manufacturer’s instructions.
If you have any comments or questions concerning the functioning of the
machine or warranty, please contact us:
STATUS d. o. o. Metlika
Ulica Belokranjskega odreda 19, 8330 Metlika, Slovenia
Customer phone: +386 736 91 230
E-mail: [email protected]
For more information visit our website www.status-innovations.eu.
6. WARRANTY
7. ELECTRIC VACUUM PUMP BVP130 SET
The set includes:
• 1 electric vacuum pump BVP130
• 1 charging cable USB 2.0/micro USB
• 1 user manual
2. USE
innovations
izvirni pripomočki
izvorna pomagala
innovations
izvirni pripomočki
izvorna pomagala
innovations
izvirni pripomočki
izvorna pomagala
2.3. CHARGING
a.) The electric vacuum pump usually needs to be charged before
first use. Insert the smaller USB connector (micro USB) into the
port at the top of the pump and the larger USB connector (USB
2.0) into an electric adapter with a USB port.
b.) The pump can be charged by using an adapter, a portable battery
(5 V , in 800 mA), or by plugging it into a USB port (USB 2.0) of a
computer or a laptop. In this case the charging speed depends on
the USB port’s use: if the USB port is intended for data-transfer
only, the battery charging will take longer, and if it is intended for
charging electronic devices, the charging will be faster. It usually
takes 2 to 4 hours for the pump to be fully charged.
c.) The indicator light flashes red during the charging of the device.
d.) The charging is complete when the indicator light changes from
red to green.
e.) To maintain the optimal functioning of the battery, charge it at
least once every 3 to 6 months.
1.3. MAINTENANCE AND CLEANING
a.) Before cleaning, unplug the adapter.
b.) Store the USB charging cable and the device
in a dry and ventilated place.
c.) Use a soft, dry or slightly damp cloth to clean
the device. Do not use sponges, coarse
cloth, polishing agents, disinfectants, or
aggressive cleaning agents that may damage
the surface of the device. Never immerse
the device in water or put it under running
water. Never spray cleaning agents directly
on the inside or outside of the device.
d.) The device must be completely dry before
use.
e.) If liquid enters the interior of the device, con-
sult the seller or authorised repair service.
