State Water Heaters GP6 50 Series Instruction Manual Download

Page: 1 / 56

Instruction Manual

PRINTED 0413

322289-002

Keep thIs Manual In the pocKet on heater for future reference

whenever MaIntenance adjustMent or servIce Is requIred.

power vent/power dIrect vent Gas Models

wIth hot surface IGnItIon

Model Gp6 50 (Y,h)tpdt serIes 124/125

complies with scaqMd low nox rule 1146.2

all technIcal and warrantY questIons:

SHOULD BE DIRECTED TO THE LOCAL DEALER FROM WHOM THE WATER HEATER WAS

PURCHASED. IF YOU ARE UNSUCCESSFUL, CALL THE TECHNICAL SUPPORT PHONE NUMBER SHOWN ON THE WATER HEATER LABELING.

resIdentIal Gas water heaters

•

for Your safety

•

AN ODORANT IS ADDED TO THE GAS USED

BY THIS WATER HEATER.

Thank you for buying this energy efficient water heater.

We appreciate your confidence in our products.

Ashland City, TN 37015

www.statewaterheaters.com

Summary of Contents for GP6 50 Series
























































Search results

Summary of Contents for GP6 50 Series

Reviews:

Related manuals for GP6 50 Series

Brands by name

Popular brands

State Water Heaters GP6 50 Series, Instruction Manual

Search results

Summary of Contents for GP6 50 Series

Reviews:

Related manuals for GP6 50 Series

Brands by name

Popular brands