manualshive.com logo in svg

Starfire SF-2400, Quick User Manual

Share
Download
Starfire SF-2400 Quick User Manual Download Page 26

BeiJing Starfire Control Technology Co.,Ltd

                     WeChat:18901200180

        QQ: 1908817881

 

26 

 

Chapter 6    parameter setting 

Press [F4] in the main screen to enter the parameter screen, as shown in the figure below:

 

 

Menu description: 

[speed] : set speed related parameters. 

[system] : set coordinate system, electronic gear and other related parameters. 

[flame] : set parameters related to flame process. 

[plasma] : setting parameters related to plasma process. 

[control] : set external signals and other relevant parameters. 

[save] : save parameters. 

[advanced] : backup, restore, import, export parameters and switch the metric system. 

6.1 speed parameters 

[starting speed] : the starting speed of the motor, the recommended value of the stepping motor is 200-500, and the 

recommended value of the servo motor is 1000. 

 

[adjustment time] : motor speed regulation time, the smaller the time, the faster the rise and fall speed, but too fast 

will cause the motor to block or machine vibration, the recommended value is 0.3. 

Summary of Contents for SF-2400













































Reviews:

No comments

Brands by name

Popular brands

Load more brands