Star SP712 Series Hardware Manual Download Page 18

Page: 18 / 40

– 14 –

< Current Setting >

Auto Connection : OFF

To enable this setting, turn

Printer Power OFF and turn ON.

PAIR

RST

PAIR

RST

RST button

3-8-4. Setting up Auto Connection

◆

Setting up from the Main Unit for the SP742

Note: The following procedure explains how to change the Auto Connection function setting from ON to OFF.

If you want to change it from OFF to ON, please follow the same procedure.

(1) When paper is loaded in the printer and it is turned on, the [POWER] LED(green) on the front of the

printer turns on.

(2) If you hold down the [RST] button on the back of the printer for at more than five seconds, initial operations are

performed in the same way as when the power is turned on, and the LEDs on the front of the printer flash. If you

press the [RST] button when the printer is placed upright, place it horizontally again while the LED is flashing.

(3) The following information is printed. After that, turn the printer off and then back on again to set "Auto

Connection" to OFF.

(4) To make sure "Auto Connection" is set to OFF correctly, perform self-printing as described in "5-4-1. Self

Printing Mode"

Setting from the Software

After pairing your device and the SP700, change "Auto Connection" in the following application provided by our

company.

iOS: Download "Star Setting Utility" from the following Web site.

http://www.star-m.jp/prjump/000003.html

Android: Download "Star Setting Utility" from the following Web site.

http://www.star-m.jp/prjump/000004.html

Windows: Download "Star Bluetooth Utility" from the following Web site.

http://www.star-m.jp/prjump/000006.html

Summary of Contents for SP712 Series









































Search results

Summary of Contents for SP712 Series

Reviews:

Related manuals for SP712 Series

Brands by name

Popular brands

Star SP712 Series, Hardware Manual

Search results

Summary of Contents for SP712 Series

Reviews:

Related manuals for SP712 Series

Brands by name

Popular brands